#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); // Set the LCD I2C address
#define Start 4 // start stop button
int hours = 0;
int minutes = 0;
int seconds = 0;
boolean timeState = false;
#define encoderPinA 2 // right
#define encoderPinB 3 // left
#define encoderButton 5 // switch
int HMS = 1;
int encoderPos = 0; // a counter for the dial
unsigned int lastReportedPos = 1; // change management
static boolean rotating = false; // debounce management
boolean A_set = false;
boolean B_set = false;

void setup() {

pinMode(Start, INPUT_PULLUP);
pinMode(encoderPinA, INPUT_PULLUP); //enabling pullups
pinMode(encoderPinB, INPUT_PULLUP);
pinMode(encoderButton, INPUT_PULLUP);
attachInterrupt(0, doEncoderA, CHANGE); //pin 2
attachInterrupt(1, doEncoderB, CHANGE); //pin 3

Serial.begin(9600); // output

lcd.begin(16, 2); // initialize the lcd for 16 chars 2 lines, turn on backlight
lcd.clear();
lcd.setCursor(0, 0);
lcd.print("COUNT DOWN TIMER");
lcd.setCursor(4, 1);
lcd.print("00:00:00");

}

void loop() {

if (digitalRead(encoderButton) == LOW)
{
HMS = HMS + 1;
if (HMS == 4)
{
HMS = 1;
}
delay(1000);
}
rotating = true; // reset the debouncer
encoderPos = constrain(encoderPos, -1, 1);
if (lastReportedPos != encoderPos) {

if (HMS == 1) {
hours = hours + encoderPos;
hours = constrain(hours, 0, 48);
}
else if (HMS == 2) {
minutes = minutes + encoderPos;
minutes = constrain(minutes, 0, 60);
}
else if (HMS == 3) {
seconds = seconds + encoderPos;
seconds = constrain(seconds, 0, 60);
}
 //Serial.println(encoderPos); // for testing
// Serial.print("hours ");
// Serial.println(hours);
// Serial.print("minutes ");
// Serial.println(minutes);
// Serial.print("seconds ");
// Serial.println(seconds);
// Serial.println(" ");
lcd.setCursor(4, 1);
if (hours <= 9)
{
lcd.print("0");
}
lcd.print(hours);
lcd.print(":");
if (minutes <= 9)
{
lcd.print("0");
}
lcd.print(minutes);
lcd.print(":");
if (seconds <= 9)
{
lcd.print("0");
}
lcd.print(seconds);
encoderPos = 0;
lastReportedPos = encoderPos;

}
if (digitalRead(Start) == LOW) { //start count down timer
timeState = true;
//delay(1000);
while (timeState == true) {
if (minutes == 0 && hours >= 1) {
minutes = 60;
hours = hours - 1;
}
if (seconds == 0 && minutes >= 1) {
seconds = 60;
minutes = minutes - 1;
}
else if (minutes == 0 && hours == 0 && seconds == 0) { //count down alarm
while (timeState == true) {
tone(11, 600, 250);
delay(250);
tone(11, 800, 250);
delay(250);
if (digitalRead(Start) == LOW) { // turn alarm off
timeState = false;
seconds = 1; 
lcd.clear();
lcd.setCursor(0, 0);
lcd.print("COUNT DOWN TIMER");
lcd.setCursor(4, 1);
lcd.print("00:00:00");

break;
}
}
}
delay(992); // delay for keping time master setting
seconds = seconds - 1;
//Serial.print("hours "); // for testing
//Serial.println(hours);
//Serial.print("minutes ");
//Serial.println(minutes);
//Serial.print("seconds ");
// Serial.println(seconds);
//Serial.println(" ");

lcd.setCursor(4, 1);
if (hours <= 9)
{
lcd.print("0");
}
lcd.print(hours);
lcd.print(":");
if (minutes <= 9)
{
lcd.print("0");
}
lcd.print(minutes);
lcd.print(":");
if (seconds <= 9)
{
lcd.print("0");
}
lcd.print(seconds);

if (digitalRead(Start) == LOW) {
delay(1000);
timeState = false;
break;
}
}
}
}

// Interrupt on A changing state
void doEncoderA() {
// debounce
if ( rotating ) delay (1); // wait a little until the bouncing is done

// Test transition, did things really change?
if ( digitalRead(encoderPinA) != A_set ) { // debounce once more
A_set = !A_set;

// adjust counter + if A leads B
if ( A_set && !B_set )
encoderPos = 1;

rotating = false; // no more debouncing until loop() hits again
}
}

// Interrupt on B changing state
void doEncoderB() {
if ( rotating ) delay (1);
if ( digitalRead(encoderPinB) != B_set ) {
B_set = !B_set;
// adjust counter - 1 if B leads A
if ( B_set && !A_set )
encoderPos = -1;

rotating = false;
}
}