#include <Wire.h>
#include <LiquidCrystal.h>

LiquidCrystal lcd(12, 11, 10, 9, 8, 7);
/*#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); //LiquidCrystal_I2C lcd(0x20,20,4);  // set the LCD address to 0x27 for a 16 chars and 2 line display or 20 chars and 4 line display

//#include <LiquidCrystal.h>
//LiquidCrystal lcd(3,4,5,6,7,8);*/
#define up 3
#define down 2
#define input_power analogRead(A0)
#define input_reflected analogRead(A1)
#define input_rf_in analogRead(A2)
#define input_temp_1 analogRead(A3)
#define input_temp_2 analogRead(A3)
#define input_temp_3 analogRead(A3)
#define input_arus_1 analogRead(A4)
#define input_arus_2 analogRead(A4)
#define input_arus_3 analogRead(A4)
#define input_vcc_1 analogRead(A5)
#define input_vcc_2 analogRead(A5)
#define input_vcc_3 analogRead(A5)
#define input_load_1 digitalRead(4)
#define input_load_2 digitalRead(5)
#define input_load_3 digitalRead(5)
#define output_dip_1 digitalWrite(4, HIGH)
#define output_dip_2 digitalWrite(5, HIGH)
#define output_dip_3 digitalWrite(6, HIGH);
#define output_dip_4 digitalWrite(13, HIGH);
//#define res 10
//#define Clear 5
//#define FAN 9
//#define batt 8
//#define AC A3
//#define Temp A2
//#define load1 6
//#define load2 7



int power = 0;
float reflected = 0;
float rf_in = 0;
float temp_1 = 10;
float temp_2 = 10;
float temp_3 = 10;
float arus_1 = 20;
float arus_2 = 20;
float arus_3 = 20;
float vcc_1 = 30;
float vcc_2 = 30;
float vcc_3 = 30;
float load_1 = 40;
float load_2 = 40;
float load_3 = 40;
int menu = 1;
int drive = 13;
int input = 0;
int downsel=0;

void setup() {
 //lcd.init();  // initialize the lcd 
 //lcd.backlight();
 lcd.begin(20,4);
 pinMode(up,INPUT_PULLUP);
 pinMode(down,INPUT_PULLUP);
 //pinMode(res,INPUT_PULLUP);
 //pinMode(Clear,INPUT_PULLUP);
 //pinMode(FAN,OUTPUT);
 //pinMode(batt,INPUT);
 //pinMode(AC,INPUT);
 //pinMode(load1,OUTPUT);
 //pinMode(load2,OUTPUT);
 pinMode(input_temp_1,INPUT);
 pinMode(input_power, INPUT);
 pinMode(input_reflected, INPUT);
 pinMode(input_rf_in, INPUT);
 pinMode(input_arus_1, INPUT);
 pinMode(input_arus_2, INPUT);
 pinMode(input_arus_3, INPUT);
 pinMode(input_vcc_1, INPUT);
 pinMode(input_vcc_2, INPUT);
 pinMode(input_vcc_3, INPUT);
 pinMode(input_load_1, INPUT);
 pinMode(input_load_2, INPUT);
 pinMode(input_load_3, INPUT);
 /* pinMode(A3, INPUT);
 pinMode(A4, INPUT);
 pinMode(A5, INPUT);
 pinMode(A6, INPUT);
 pinMode(A7, INPUT); */

 pinMode(drive, OUTPUT);
// pinMode(led,OUTPUT);

 welcome();

 //lcd.setCursor(0, 0);
// lcd.write(byte(0)); // when calling lcd.write() '0' must be cast as a byte
// lcd.setCursor(0,1);  
// lcd.write(1);
// lcd.setCursor(0,2);  
// lcd.write(2);
// lcd.setCursor(0,3);  
// lcd.write(3);
// lcd.setCursor(1,0);  
//lcd.write(4);
 // lcd.setCursor(1,1);  
// lcd.write(5);
}

void welcome(){
  lcd.setCursor(0,0);
  lcd.print("WELCOME TO ");
  lcd.setCursor(5,1);
  lcd.print("TONY-TECH PRO");
  lcd.setCursor(3,2);
  lcd.print("Electrical and ");
  lcd.setCursor(0,3);
  lcd.print("Electronics Services");
  digitalWrite(13, HIGH);
  delay(1000);
  lcd.clear();
}

void home(){
powers();
reflecteds();
rfpowers();
//temps();
//arusflow();
//voltages();
//loads();
//pll();

}

void powers(){
  lcd.clear();
  lcd.setCursor(0,0); 
  lcd.print("RF POWER Status"); 
  lcd.setCursor(0,1);  //formula using for perform action power
  lcd.print("POWER:          WATT");
  lcd.setCursor(7,1);
  lcd.print(power);
}


void reflecteds(){  //formula using for perform action power
  lcd.setCursor(0,2);
  lcd.print("REF  :          WATT");
  lcd.setCursor(7,2);
  lcd.print(reflected);
}

void rfpowers(){
  lcd.setCursor(0,3);   //formula using for perform action power
  lcd.print("RF IN:          WATT");
  lcd.setCursor(7,3);
  lcd.print(rf_in);
}

void temps(){
  lcd.clear();
  lcd.setCursor(0,0); 
  lcd.print("TEMP Status"); 
  lcd.setCursor(0,1);//formula using for perform action power
  lcd.print("TEMP 1:          C");
  //
  lcd.setCursor(7,1);
  lcd.print(temp_1);
  lcd.setCursor(0,2); //formula using for perform action power
  lcd.print("TEMP 2:          C");
  lcd.setCursor(7,2);
  lcd.print(temp_2);
  //
  lcd.setCursor(0,3);   //formula using for perform action power
  lcd.print("TEMP 3:          C");
  lcd.setCursor(7,3);
  lcd.print(temp_3);
   delay(150);
}

void arusflow(){
  lcd.clear();
  lcd.setCursor(0,0); 
  lcd.print("ARUS Status"); 
  lcd.setCursor(0,1);  //formula using for perform action power
  lcd.print("ARUS 1:          A");
  lcd.setCursor(7,1);
  lcd.print(arus_1);
  //
  lcd.setCursor(0,2);    //formula using for perform action power
  lcd.print("ARUS 2:          A");
  lcd.setCursor(7,2);
  lcd.print(arus_2);
  //
  lcd.setCursor(0,3);    //formula using for perform action power
  lcd.print("ARUS 3:          A");
  lcd.setCursor(7,3);
  lcd.print(arus_2);
   delay(150);
}

void voltages(){
  lcd.clear();
  lcd.setCursor(2,0); 
  lcd.print("DC VOLTAGE  Status"); 
  lcd.setCursor(0,1);
  lcd.print("VCC 1:           V");
  lcd.setCursor(7,1);
  lcd.print(vcc_1);
  //
  lcd.setCursor(0,2);
  lcd.print("VCC 2:           V");
  lcd.setCursor(7,2);
  lcd.print(vcc_2);
  //
  lcd.setCursor(0,3);
  lcd.print("VCC 3:           V");
  lcd.setCursor(7,3);
  lcd.print(vcc_3);    
  delay(150);
}

void loads(){
  lcd.clear();
  lcd.setCursor(2,0); 
  lcd.print("DC POWER  Status"); 
  lcd.setCursor(0,1);
  lcd.print("LOAD 1:       WATT");
  lcd.setCursor(7,1);
  lcd.print(load_1);
  //
  lcd.setCursor(0,2);
  lcd.print("LOAD 2:       WATT");
  lcd.setCursor(7,2);
  lcd.print(load_2);
  //
  lcd.setCursor(0,3);
  lcd.print("LOAD 3:       WATT");
  lcd.setCursor(7,3);
  lcd.print(load_3);    
  delay(150);

}

void pll(){
  lcd.clear();
  lcd.setCursor(2,0); 
  lcd.print("PLL SETUP  Status"); 
  lcd.setCursor(0,1);
  lcd.print("FREKUE:       MHZ");
  lcd.setCursor(7,1);
  lcd.print(load_1);
  //
  lcd.setCursor(0,2);
  lcd.print("LOAD 2:       WATT");
  lcd.setCursor(7,2);
  lcd.print(load_2);
  //
  lcd.setCursor(0,3);
  lcd.print("LOAD 3:       WATT");
  lcd.setCursor(7,3);
  lcd.print(load_3);    
  delay(150);

}

void bgProses(){
  //input = (input_power);           //analogRead function is used to recive analog data Power
  power = (input_power * 200.0) / 1024.0; 

  //input = analogRead(A1);           //analogRead function is used to recive analog data Power
  reflected = (input_reflected * 20.0) / 1024.0; 

  //input = analogRead(A2);           //analogRead function is used to recive analog data Power
  rf_in = (input_rf_in * 20.0) / 1024.0; 

  //input = analogRead(A2);           //analogRead function is used to recive analog data Power
  temp_1 = (input_temp_1 * 20.0) / 1024.0;

  //input = analogRead(A2);           //analogRead function is used to recive analog data Power
  temp_2 = (input_temp_2 * 20.0) / 1024.0;  

  //input = analogRead(A2);           //analogRead function is used to recive analog data Power
  temp_3 = (input_temp_3 * 20.0) / 1024.0;

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  arus_1 = (input_arus_1 * 30.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  arus_2 = (input_arus_2 * 30.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  arus_3 = (input_arus_3 * 30.0) / 1024.0;

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  vcc_1 = (input_vcc_1 * 40.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  vcc_2 = (input_vcc_2 * 40.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  vcc_3 = (input_vcc_3 * 40.0) / 1024.0;

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  load_1 = (input_vcc_1 * 50.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  load_2 = (input_vcc_2 * 50.0) / 1024.0;  

  //input = analogRead(A3);           //analogRead function is used to recive analog data Power
  load_3 = (input_vcc_3 * 50.0) / 1024.0; 
}


// TAMPILAN MENU HOME STATUS SYSTEM
void status(){
lcd.clear();
switch(downsel){
  case 0:
    home();
    bgProses();
    delay(100);
    break;
  case 1:  
    temps();
    bgProses();
    delay(100);
    break;
  case 2:
    arusflow();
    bgProses();
    delay(100);
    break;
  case 3:
    voltages();
    bgProses();
    delay(100);
    break;
  case 4:
    loads();
    bgProses();   
    delay(100);
    break;
  case 5:
    pll();
    bgProses();   
    delay(100);
    break;
    }
    if(digitalRead(down) == LOW){ 
      downsel++;
      if(downsel > 5){
        downsel = 0;
      }
      delay(10);
    }
    if(digitalRead(up)== LOW){
      downsel--;
      if(downsel < 0){
        downsel = 5;
      }
      delay(10);
    }
    delay(100);
}


// PEMPROSESAN PROGRAM SYSTEM
// diskripsi [ jika refledted lebih besar dari 20 maka pin 13 high dan print high reflected]
// diskripsi [ jika rf in lebih besar dari 20 maka pin 13 high dan print over drive]
// diskripsi [ jika temperatur lebih besar dari 40 maka pin 13 high dan print high temperatur]
// diskripsi [ jika arus lebih besar dari 30 maka pin 13 high dan print high arus]
// diskripsi [ jika semua status dibawah nilai maka system kemali ke normal {void loop di status saja}]

void loop() {
  status();
  digitalWrite(13, LOW);
  while(power > 900){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("HIGH POWER");
    delay(150);
    bgProses();
    if(power < 900){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }

  while(reflected > 17){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("HIGH REFL");
    delay(150);
    bgProses();
    if(reflected < 17){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }

  while(rf_in > 15){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("OVER DRIVE");
    delay(150);
    bgProses();
    if(rf_in < 15){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }

  /*while(reflected > 17){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("HIGH REFL");
    delay(150);
    bgProses();
    if(reflected < 17){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }

  while(reflected > 17){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("HIGH REFL");
    delay(150);
    bgProses();
    if(reflected < 17){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }

  while(reflected > 17){
    digitalWrite(13,HIGH);
    digitalWrite(6,HIGH);
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("HIGH REFL");
    delay(150);
    bgProses();
    if(reflected < 17){
      digitalWrite(13, LOW);
      digitalWrite(6, LOW);
      return 0;
    }
  }*/
}