// Use the MD_MAX72XX library to Display a Daft Punk LED Helmet
//
// If RUN_DEMO is set to zero the display cycles changes triggered by a switch on
// the MODE_SWITCH pin. This can be substituted for any trigger as implemented
// by the helmet wearer.
// If RUN_DEMO is set to 1 the sketch will cycle each element of the display every
// DEMO_DELAY seconds, without the need for a switch.
//
// Uses the MD_UISwitch library found at https://github.com/MajicDesigns/MD_UISwitch

/* CONNECTIONS :--
 *VCC       5V of Arduino 
 *GND       Gnd of Arduino 
 *CLK PIN   Pin 13  
 *DATA PIN  Pin 11  
 *CS PIN    Pin 10  */


#define RUN_DEMO  1

#include <MD_MAX72xx.h>
#include <SPI.h>

#if RUN_DEMO
#define DEMO_DELAY  15  // time to show each demo element in seconds
#else
#include <MD_UISwitch.h>
#endif

#define DEBUG 0   // Enable or disable (default) debugging output

#if DEBUG
#define PRINT(s, v)   { Serial.print(F(s)); Serial.print(v); }        // Print a string followed by a value (decimal)
#define PRINTX(s, v)  { Serial.print(F(s)); Serial.print(v, HEX); }   // Print a string followed by a value (hex)
#define PRINTB(s, v)  { Serial.print(F(s)); Serial.print(v, BIN); }   // Print a string followed by a value (binary)
#define PRINTC(s, v)  { Serial.print(F(s)); Serial.print((char)v); }  // Print a string followed by a value (char)
#define PRINTS(s)     { Serial.print(F(s)); }                         // Print a string
#else
#define PRINT(s, v)   // Print a string followed by a value (decimal)
#define PRINTX(s, v)  // Print a string followed by a value (hex)
#define PRINTB(s, v)  // Print a string followed by a value (binary)
#define PRINTC(s, v)  // Print a string followed by a value (char)
#define PRINTS(s)     // Print a string
#endif

// --------------------
// MD_MAX72xx hardware definitions and object
// Define the number of devices we have in the chain and the hardware interface
// NOTE: These pin numbers will probably not work with your hardware and may
// need to be adapted
//
#define HARDWARE_TYPE MD_MAX72XX::PAROLA_HW
#define MAX_DEVICES 4
#define CLK_PIN   13
#define DATA_PIN  11
#define CS_PIN    10

MD_MAX72XX mx = MD_MAX72XX(HARDWARE_TYPE, CS_PIN, MAX_DEVICES);                      // SPI hardware interface
//MD_MAX72XX mx = MD_MAX72XX(HARDWARE_TYPE, DATA_PIN, CLK_PIN, CS_PIN, MAX_DEVICES); // Arbitrary pins

#if !RUN_DEMO
// --------------------
// Mode keyswitch parameters and object
//
#define MODE_SWITCH 9 // Digital Pin

MD_UISwitch_Digital  ks = MD_UISwitch_Digital(MODE_SWITCH, LOW);
#endif

// --------------------
// Constant parameters
//
// Various delays in milliseconds
#define UNIT_DELAY      20
#define SCROLL_DELAY    (2 * UNIT_DELAY)
#define SCROLL_DELAY_2  (2 * UNIT_DELAY)
#define MIDLINE_DELAY   (3 * UNIT_DELAY)
#define SCANNER_DELAY   (2 * UNIT_DELAY)
#define RANDOM_DELAY    (6 * UNIT_DELAY)
#define FADE_DELAY      (8 * UNIT_DELAY)
#define SPECTRUM_DELAY  (4 * UNIT_DELAY)
#define HEARTBEAT_DELAY (1 * UNIT_DELAY)
#define HEARTS_DELAY    (28 * UNIT_DELAY)
#define EYES_DELAY      (20 * UNIT_DELAY)
#define WIPER_DELAY     (1 * UNIT_DELAY)
#define ARROWS_DELAY    (3 * UNIT_DELAY)
#define ARROWR_DELAY    (8 * UNIT_DELAY)
#define INVADER_DELAY   (4 * UNIT_DELAY)
#define PACMAN_DELAY    (4 * UNIT_DELAY)
#define SINE_DELAY      (2 * UNIT_DELAY)

#define CHAR_SPACING     1  // pixels between characters
#define BUF_SIZE        75  // character buffer size

// ========== General Variables ===========
//
uint32_t prevTimeAnim = 0;    // Used for remembering the millis() value in animations
#if RUN_DEMO
uint32_t prevTimeDemo = 0;      //  Used for remembering the millis() time in demo loop
uint8_t  timeDemo = DEMO_DELAY; // number of seconds left in this demo loop
#endif

// ========== Text routines ===========
//
// Text Message Table
// To change messages simply reorder, add to, or delete from, this table
const char *msgTab[] =
{
  "@bimo.mr",
};

bool scrollText(bool bInit, const char *pmsg)
// Callback function for data that is required for scrolling into the display
{
  static char   curMessage[BUF_SIZE];
  static char   *p = curMessage;
  static uint8_t  state = 0;
  static uint8_t  curLen, showLen;
  static uint8_t  cBuf[8];
  uint8_t         colData;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Initializing ScrollText");
    resetMatrix();
    strcpy(curMessage, pmsg);
    state = 0;
    p = curMessage;
    bInit = false;
  }

  // Is it time to scroll the text?
  if (millis()-prevTimeAnim < SCROLL_DELAY)
    return(bInit);

  // scroll the display
  mx.transform(MD_MAX72XX::TSL);  // scroll along
  prevTimeAnim = millis();        // starting point for next time

  // now run the finite state machine to control what we do
  PRINT("\nScroll FSM S:", state);
  switch (state)
  {
    case 0: // Load the next character from the font table
      PRINTC("\nLoading ", *p);
      showLen = mx.getChar(*p++, sizeof(cBuf)/sizeof(cBuf[0]), cBuf);
      curLen = 0;
      state = 1;

    // !! deliberately fall through to next state to start displaying

    case 1: // display the next part of the character
      colData = cBuf[curLen++];
      mx.setColumn(0, colData);
      if (curLen == showLen)
      {
        showLen = ((*p != '\0') ? CHAR_SPACING : mx.getColumnCount()-1);
        curLen = 0;
        state = 2;
      }
      break;

    case 2: // display inter-character spacing (blank column) or scroll off the display
      mx.setColumn(0, 0);
      if (++curLen == showLen)
      {
        state = 0;
        bInit = (*p == '\0');
      }
      break;

    default:
      state = 0;
  }

  return(bInit);
}


// ========== Text routines 2 ===========
//
// Text Message Table
// To change messages simply reorder, add to, or delete from, this table
const char *msgTab_2[] =
{
  "jaya jaya jaya",
};

bool scrollText_2(bool bInit, const char *pmsg)
// Callback function for data that is required for scrolling into the display
{
  static char   curMessage[BUF_SIZE];
  static char   *p = curMessage;
  static uint8_t  state = 0;
  static uint8_t  curLen, showLen;
  static uint8_t  cBuf[8];
  uint8_t         colData;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Initializing ScrollText");
    resetMatrix();
    strcpy(curMessage, pmsg);
    state = 0;
    p = curMessage;
    bInit = false;
  }

  // Is it time to scroll the text?
  if (millis()-prevTimeAnim < SCROLL_DELAY_2)
    return(bInit);

  // scroll the display
  mx.transform(MD_MAX72XX::TSL);  // scroll along
  prevTimeAnim = millis();        // starting point for next time

  // now run the finite state machine to control what we do
  PRINT("\nScroll FSM S:", state);
  switch (state)
  {
    case 0: // Load the next character from the font table
      PRINTC("\nLoading ", *p);
      showLen = mx.getChar(*p++, sizeof(cBuf)/sizeof(cBuf[0]), cBuf);
      curLen = 0;
      state = 1;

    // !! deliberately fall through to next state to start displaying

    case 1: // display the next part of the character
      colData = cBuf[curLen++];
      mx.setColumn(0, colData);
      if (curLen == showLen)
      {
        showLen = ((*p != '\0') ? CHAR_SPACING : mx.getColumnCount()-1);
        curLen = 0;
        state = 2;
      }
      break;

    case 2: // display inter-character spacing (blank column) or scroll off the display
      mx.setColumn(0, 0);
      if (++curLen == showLen)
      {
        state = 0;
        bInit = (*p == '\0');
      }
      break;

    default:
      state = 0;
  }

  return(bInit);
}


// ========== Graphic routines ===========
//
bool graphicMidline1(bool bInit)
{
  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Midline1 init");
    resetMatrix();
    bInit = false;
  }
  else
  {
    for (uint8_t j=0; j<MAX_DEVICES; j++)
    {
      mx.setRow(j, 3, 0xff);
      mx.setRow(j, 4, 0xff);
    }
  }

  return(bInit);
}

bool graphicMidline2(bool bInit)
{
  static uint8_t  idx = 0;      // position
  static int8_t   idOffs = 1;   // increment direction

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Midline2 init");
    resetMatrix();
    idx = 0;
    idOffs = 1;
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < MIDLINE_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nML2 R:", idx);
  PRINT(" D:", idOffs);

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);

  // turn off the old lines
  for (uint8_t j=0; j<MAX_DEVICES; j++)
  {
    mx.setRow(j, idx, 0x00);
    mx.setRow(j, ROW_SIZE-1-idx, 0x00);
  }

  idx += idOffs;
  if ((idx == 0) || (idx == ROW_SIZE-1))
    idOffs = -idOffs;

  // turn on the new lines
  for (uint8_t j=0; j<MAX_DEVICES; j++)
  {
    mx.setRow(j, idx, 0xff);
    mx.setRow(j, ROW_SIZE-1-idx, 0xff);
  }

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicScanner(bool bInit)
{
  const uint8_t width = 3;      // scanning bar width
  static uint8_t  idx = 0;      // position
  static int8_t   idOffs = 1;   // increment direction

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Scanner init");
    resetMatrix();
    idx = 0;
    idOffs = 1;
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < SCANNER_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nS R:", idx);
  PRINT(" D:", idOffs);

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);

  // turn off the old lines
  for (uint8_t i=0; i<width; i++)
    mx.setColumn(idx+i, 0);

  idx += idOffs;
  if ((idx == 0) || (idx + width == mx.getColumnCount()))
    idOffs = -idOffs;

  // turn on the new lines
  for (uint8_t i=0; i<width; i++)
    mx.setColumn(idx+i, 0xff);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicRandom(bool bInit)
{
  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Random init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < RANDOM_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  for (uint8_t i=0; i<mx.getColumnCount(); i++)
    mx.setColumn(i, (uint8_t)random(255));
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicScroller(bool bInit)
{
  const uint8_t   width = 3;     // width of the scroll bar
  const uint8_t   offset = mx.getColumnCount()/3;
  static uint8_t  idx = 0;      // counter

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Scroller init");
    resetMatrix();
    idx = 0;
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < SCANNER_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nS I:", idx);

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);

  mx.transform(MD_MAX72XX::TSL);

  mx.setColumn(0, idx>=0 && idx<width ? 0xff : 0);
  if (++idx == offset) idx = 0;

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicSpectrum1(bool bInit)
{
  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Spectrum1 init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < SPECTRUM_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  for (uint8_t i=0; i<MAX_DEVICES; i++)
  {
    uint8_t r = random(ROW_SIZE);
    uint8_t cd = 0;

    for (uint8_t j=0; j<r; j++)
      cd |= 1<<j;
    for (uint8_t j=1; j<COL_SIZE-1; j++)
      mx.setColumn(i, j, ~cd);
  }
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicSpectrum2(bool bInit)
{
  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Spectrum2init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis() - prevTimeAnim < SPECTRUM_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  for (uint8_t i = 0; i<mx.getColumnCount(); i++)
  {
    uint8_t r = random(ROW_SIZE);
    uint8_t cd = 0;

    for (uint8_t j = 0; j<r; j++)
      cd |= 1 << j;

    mx.setColumn(i, ~cd);
  }
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicHeartbeat(bool bInit)
{
  #define BASELINE_ROW  4

  static uint8_t  state;
  static uint8_t  r, c;
  static bool     bPoint;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Heartbeat init");
    resetMatrix();
    state = 0;
    r = BASELINE_ROW;
    c = mx.getColumnCount()-1;
    bPoint = true;
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < HEARTBEAT_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  PRINT("\nHB S:", state);
  PRINT(" R: ", r);
  PRINT(" C: ", c);
  PRINT(" P: ", bPoint);
  mx.setPoint(r, c, bPoint);

  switch (state)
  {
    case 0: // straight line from the right side
      if (c == mx.getColumnCount()/2 + COL_SIZE)
        state = 1;
      c--;
      break;

    case 1: // first stroke
      if (r != 0) { r--; c--; }
      else state = 2;
      break;

    case 2: // down stroke
      if (r != ROW_SIZE-1) { r++; c--; }
      else state = 3;
      break;

    case 3: // second up stroke
      if (r != BASELINE_ROW) { r--; c--; }
      else state = 4;
      break;

    case 4: // straight line to the left
      if (c == 0)
      {
        c = mx.getColumnCount()-1;
        bPoint = !bPoint;
        state = 0;
      }
      else c--;
      break;

    default:
      state = 0;
  }

  return(bInit);
}

bool graphicFade(bool bInit)
{
  static uint8_t  intensity = 0;
  static int8_t   iOffs = 1;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Fade init");
    resetMatrix();
    mx.control(MD_MAX72XX::INTENSITY, intensity);

    // Set all LEDS on
    mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
    for (uint8_t i=0; i<mx.getColumnCount(); i++)
      mx.setColumn(i, 0xff);
    mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < FADE_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  intensity += iOffs;
  PRINT("\nF I:", intensity);
  PRINT(" D:", iOffs);
  if ((intensity == 0) || (intensity == MAX_INTENSITY))
    iOffs = -iOffs;
  mx.control(MD_MAX72XX::INTENSITY, intensity);

  return(bInit);
}

bool graphicHearts(bool bInit)
{
#define NUM_HEARTS  ((MAX_DEVICES/2) +1)
  const uint8_t heartFull[] = { 0x1c, 0x3e, 0x7e, 0xfc };
  const uint8_t heartEmpty[] = { 0x1c, 0x22, 0x42, 0x84 };
  const uint8_t offset = mx.getColumnCount()/(NUM_HEARTS+1);
  const uint8_t dataSize = (sizeof(heartFull)/sizeof(heartFull[0]));

  static bool     bEmpty;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Hearts init");
    resetMatrix();
    bEmpty = true;
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < HEARTS_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  PRINT("\nH E:", bEmpty);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  for (uint8_t h=1; h<=NUM_HEARTS; h++)
  {
    for (uint8_t i=0; i<dataSize; i++)
    {
      mx.setColumn((h*offset)-dataSize+i, bEmpty ? heartEmpty[i] : heartFull[i]);
      mx.setColumn((h*offset)+dataSize-i-1, bEmpty ? heartEmpty[i] : heartFull[i]);
    }
  }
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);
  bEmpty = !bEmpty;

  return(bInit);
}

bool graphicEyes(bool bInit)
{
#define NUM_EYES  2
  const uint8_t eyeOpen[] = { 0x18, 0x3c, 0x66, 0x66 };
  const uint8_t eyeClose[] = { 0x18, 0x3c, 0x3c, 0x3c };
  const uint8_t offset = mx.getColumnCount()/(NUM_EYES+1);
  const uint8_t dataSize = (sizeof(eyeOpen)/sizeof(eyeOpen[0]));

  bool bOpen;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Eyes init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < EYES_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  bOpen = (random(1000) > 100);
  PRINT("\nH E:", bOpen);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  for (uint8_t e=1; e<=NUM_EYES; e++)
  {
    for (uint8_t i=0; i<dataSize; i++)
    {
      mx.setColumn((e*offset)-dataSize+i, bOpen ? eyeOpen[i] : eyeClose[i]);
      mx.setColumn((e*offset)+dataSize-i-1, bOpen ? eyeOpen[i] : eyeClose[i]);
    }
  }
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicBounceBall(bool bInit)
{
  static uint8_t  idx = 0;      // position
  static int8_t   idOffs = 1;   // increment direction

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- BounceBall init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < SCANNER_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nBB R:", idx);
  PRINT(" D:", idOffs);

  // now run the animation
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);

  // turn off the old ball
  mx.setColumn(idx, 0);
  mx.setColumn(idx+1, 0);

  idx += idOffs;
  if ((idx == 0) || (idx == mx.getColumnCount()-2))
    idOffs = -idOffs;

  // turn on the new lines
  mx.setColumn(idx, 0x18);
  mx.setColumn(idx+1, 0x18);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicArrowScroll(bool bInit)
{
  const uint8_t arrow[] = { 0x3c, 0x66, 0xc3, 0x99 };
  const uint8_t dataSize = (sizeof(arrow)/sizeof(arrow[0]));

  static uint8_t  idx = 0;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- ArrowScroll init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < ARROWS_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  PRINT("\nAR I:", idx);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  mx.transform(MD_MAX72XX::TSL);
  mx.setColumn(0, arrow[idx++]);
  if (idx == dataSize) idx = 0;
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicWiper(bool bInit)
{
  static uint8_t  idx = 0;      // position
  static int8_t   idOffs = 1;   // increment direction

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Wiper init");
    resetMatrix();
    bInit = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < WIPER_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nW R:", idx);
  PRINT(" D:", idOffs);

  // now run the animation
  mx.setColumn(idx, idOffs == 1 ? 0xff : 0);
  idx += idOffs;
  if ((idx == 0) || (idx == mx.getColumnCount()))
    idOffs = -idOffs;

  return(bInit);
}

bool graphicInvader(bool bInit)
{
  const uint8_t invader1[] = { 0x0e, 0x98, 0x7d, 0x36, 0x3c };
  const uint8_t invader2[] = { 0x70, 0x18, 0x7d, 0xb6, 0x3c };
  const uint8_t dataSize = (sizeof(invader1)/sizeof(invader1[0]));

  static int8_t idx;
  static bool   iType;

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Invader init");
    resetMatrix();
    bInit = false;
    idx = -dataSize;
    iType = false;
  }

  // Is it time to animate?
  if (millis()-prevTimeAnim < INVADER_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  // now run the animation
  PRINT("\nINV I:", idx);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  mx.clear();
  for (uint8_t i=0; i<dataSize; i++)
  {
    mx.setColumn(idx-dataSize+i, iType ? invader1[i] : invader2[i]);
    mx.setColumn(idx+dataSize-i-1, iType ? invader1[i] : invader2[i]);
  }
  idx++;
  if (idx == mx.getColumnCount()+(dataSize*2)) bInit = true;
  iType = !iType;
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicPacman(bool bInit)
{
  #define MAX_FRAMES  4   // number of animation frames
  #define PM_DATA_WIDTH  18
  const uint8_t pacman[MAX_FRAMES][PM_DATA_WIDTH] =  // ghost pursued by a pacman
  {
    { 0x3c, 0x7e, 0x7e, 0xff, 0xe7, 0xc3, 0x81, 0x00, 0x00, 0x00, 0x00, 0xfe, 0x7b, 0xf3, 0x7f, 0xfb, 0x73, 0xfe },
    { 0x3c, 0x7e, 0xff, 0xff, 0xe7, 0xe7, 0x42, 0x00, 0x00, 0x00, 0x00, 0xfe, 0x7b, 0xf3, 0x7f, 0xfb, 0x73, 0xfe },
    { 0x3c, 0x7e, 0xff, 0xff, 0xff, 0xe7, 0x66, 0x24, 0x00, 0x00, 0x00, 0xfe, 0x7b, 0xf3, 0x7f, 0xfb, 0x73, 0xfe },
    { 0x3c, 0x7e, 0xff, 0xff, 0xff, 0xff, 0x7e, 0x3c, 0x00, 0x00, 0x00, 0xfe, 0x7b, 0xf3, 0x7f, 0xfb, 0x73, 0xfe },
  };

  static int16_t idx;        // display index (column)
  static uint8_t frame;      // current animation frame
  static uint8_t deltaFrame; // the animation frame offset for the next frame

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Pacman init");
    resetMatrix();
    bInit = false;
    idx = -1; //DATA_WIDTH;
    frame = 0;
    deltaFrame = 1;
  }

  // Is it time to animate?
  if (millis() - prevTimeAnim < PACMAN_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  PRINT("\nPAC I:", idx);

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
  mx.clear();

  // clear old graphic
  for (uint8_t i = 0; i<PM_DATA_WIDTH; i++)
    mx.setColumn(idx - PM_DATA_WIDTH + i, 0);
  // move reference column and draw new graphic
  idx++;
  for (uint8_t i = 0; i<PM_DATA_WIDTH; i++)
    mx.setColumn(idx - PM_DATA_WIDTH + i, pacman[frame][i]);

  // advance the animation frame
  frame += deltaFrame;
  if (frame == 0 || frame == MAX_FRAMES - 1)
    deltaFrame = -deltaFrame;

  // check if we are completed and set initialize for next time around
  if (idx == mx.getColumnCount() + PM_DATA_WIDTH) bInit = true;

  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);

  return(bInit);
}

bool graphicArrowRotate(bool bInit)
{
  static uint16_t idx;        // transformation index

  uint8_t arrow[COL_SIZE] =
  {
    0b00000000,
    0b00011000,
    0b00111100,
    0b01111110,
    0b00011000,
    0b00011000,
    0b00011000,
    0b00000000
  };

  MD_MAX72XX::transformType_t  t[] =
  {
    MD_MAX72XX::TRC, MD_MAX72XX::TRC,
    MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR, MD_MAX72XX::TSR,
    MD_MAX72XX::TRC, MD_MAX72XX::TRC,
    MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL, MD_MAX72XX::TSL,
    MD_MAX72XX::TRC,
  };

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- ArrowRotate init");
    resetMatrix();
    bInit = false;
    idx = 0;

    // use the arrow bitmap
    mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::OFF);
    for (uint8_t j = 0; j<mx.getDeviceCount(); j++)
      mx.setBuffer(((j + 1)*COL_SIZE) - 1, COL_SIZE, arrow);
    mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);
  }

  // Is it time to animate?
  if (millis() - prevTimeAnim < ARROWR_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  mx.control(MD_MAX72XX::WRAPAROUND, MD_MAX72XX::ON);
  mx.transform(t[idx++]);
  mx.control(MD_MAX72XX::WRAPAROUND, MD_MAX72XX::OFF);

  // check if we are completed and set initialize for next time around
  if (idx == (sizeof(t) / sizeof(t[0]))) bInit = true;

  return(bInit);
}

bool graphicSinewave(bool bInit)
{
  static uint8_t curWave = 0;
  static uint8_t idx;

  #define SW_DATA_WIDTH  11    // valid data count followed by up to 10 data points
  const uint8_t waves[][SW_DATA_WIDTH] =
  {
    {  9,   8,  6,   1,   6,  24,  96, 128,  96,  16,   0 },
    {  6,  12,  2,  12,  48,  64,  48,   0,   0,   0,   0 },
    { 10,  12,   2,   1,   2,  12,  48,  64, 128,  64, 48 },

  };
  const uint8_t WAVE_COUNT = sizeof(waves) / (SW_DATA_WIDTH * sizeof(uint8_t));

  // are we initializing?
  if (bInit)
  {
    PRINTS("\n--- Sinewave init");
    resetMatrix();
    bInit = false;
    idx = 1;
  }

  // Is it time to animate?
  if (millis() - prevTimeAnim < SINE_DELAY)
    return(bInit);
  prevTimeAnim = millis();    // starting point for next time

  mx.control(MD_MAX72XX::WRAPAROUND, MD_MAX72XX::ON);
  mx.transform(MD_MAX72XX::TSL);
  mx.setColumn(0, waves[curWave][idx++]);
  if (idx > waves[curWave][0])
  {
    curWave = random(WAVE_COUNT);
    idx = 1;
  }
  mx.control(MD_MAX72XX::WRAPAROUND, MD_MAX72XX::OFF);

  return(bInit);
}

// ========== Control routines ===========
//
void resetMatrix(void)
{
  mx.control(MD_MAX72XX::INTENSITY, MAX_INTENSITY/2);
  mx.control(MD_MAX72XX::UPDATE, MD_MAX72XX::ON);
  mx.clear();
  prevTimeAnim = 0;
}

void runMatrixAnimation(void)
// Schedule the animations, switching to the next one when the
// the mode switch is pressed.
{
  static  uint8_t state = 0;
  static  uint8_t mesg = 0;
  static  boolean bRestart = true;
  static boolean  bInMessages = false;
  boolean changeState = false;

#if RUN_DEMO
  // check if one second has passed and then count down the demo timer. Once this
  // gets to zero, change the state.
  if (millis()-prevTimeDemo >= 600)
  {
    prevTimeDemo = millis();
    if (--timeDemo == 0)
    {
      timeDemo = DEMO_DELAY;
      changeState = true;
    }
  }
#else
  // check if the switch is pressed and handle that first
  changeState = (ks.read() == MD_UISwitch::KEY_PRESS);
#endif
  if (changeState)
  {
    if (bInMessages) // the message display state
    {
      mesg++;
      if (mesg >= sizeof(msgTab)/sizeof(msgTab[0]))
      {
        mesg = 0;
      bInMessages = false;
        state++;
      }
    }
    else
      state++;

    bRestart = true;
  };

  // now do whatever we do in the current state
  switch(state)
  {
    case 0: bInMessages = true; bRestart = scrollText(bRestart, msgTab[mesg]); break;
    case 1: bInMessages = true; bRestart = scrollText_2(bRestart, msgTab_2[mesg]); break;
    // case  2: bRestart = graphicMidline1(bRestart);       break;
    case 2: bRestart = graphicMidline2(bRestart);       break;
    case 3: bRestart = graphicScanner(bRestart);        break;
    case 4: bRestart = graphicRandom(bRestart);         break;
    // case 5: bRestart = graphicFade(bRestart);           break;
    case 5: bRestart = graphicSpectrum1(bRestart);      break;
    case 6: bRestart = graphicHeartbeat(bRestart);      break;
    case 7: bRestart = graphicHearts(bRestart);         break;
    case 8: bRestart = graphicEyes(bRestart);           break;
    case 9: bRestart = graphicBounceBall(bRestart);     break;
    case 10: bRestart = graphicArrowScroll(bRestart);    break;
    case 11: bRestart = graphicScroller(bRestart);       break;
    case 12: bRestart = graphicWiper(bRestart);          break;
    case 13: bRestart = graphicInvader(bRestart);        break;
    case 14: bRestart = graphicPacman(bRestart);         break;
    case 15: bRestart = graphicArrowRotate(bRestart);    break;
    case 16: bRestart = graphicSpectrum2(bRestart);      break;
    case 17: bRestart = graphicSinewave(bRestart);       break;

    default: state = 0;
  }
}

void setup()
{
  mx.begin();
  prevTimeAnim = millis();
#if RUN_DEMO
  prevTimeDemo = millis();
#else
  ks.begin();
#endif
#if DEBUG
  Serial.begin(57600);
#endif
  PRINTS("\n[MD_MAX72XX DaftPunk]");
}

void loop()
{
  runMatrixAnimation();
  // other code to run the helmet goes here
}