use anyhow::Result;
use embedded_hal::blocking::delay::DelayMs;
use esp_idf_svc::hal::{
    delay::FreeRtos,
    i2c::{I2cConfig, I2cDriver},
    peripherals::Peripherals,
    prelude::*,
};

// Comment out the following line to run the solution, check lib.rs for further instructions
use i2c_driver::icm42670p::{DeviceAddr, ICM42670P};

// Dont change this file. Work in the icm42670p.rs and modify it so main.rs runs.

fn main() -> Result<()> {
    esp_idf_svc::sys::link_patches();

    let peripherals = Peripherals::take().unwrap();

    let sda = peripherals.pins.gpio10;
    let scl = peripherals.pins.gpio8;

    let config = I2cConfig::new().baudrate(400.kHz().into());
    let i2c = I2cDriver::new(peripherals.i2c0, sda, scl, &config)?;

    let mut sensor = ICM42670P::new(i2c, DeviceAddr::AD0)?;

    println!("Sensor init");
    let device_id = sensor.read_device_id_register()?;

    println!("Hello, world, I am sensor {:#02x}", device_id);

    loop {
        FreeRtos.delay_ms(500u32);
    }
}


main.rs

diagram.json

#![deny(unsafe_code)]
#![no_std]

pub mod icm42670p;

lib.rs

#![deny(unsafe_code)]

use core::marker::PhantomData;
use embedded_hal::blocking::i2c;

/// ICM42670P device driver, represented by a struct with 2 fields.
/// Datasheet: https://invensense.tdk.com/wp-content/uploads/2021/07/DS-000451-ICM-42670-P-v1.0.pdf
#[derive(Debug)]
pub struct ICM42670P<I2C> {
    // The concrete I²C device implementation.
    //  TODO! field 1
    // Device address
    //  TODO! field 2
    // Remove the following line as soon as the I2C parameter is used.
    rec_type: PhantomData<I2C>,
}

// See Table 3.3.2 in Documentation
/// Contains the possible variants of the devices addesses as binary numbers.
#[derive(Debug, Clone, Copy, PartialEq)]
pub enum DeviceAddr {
    AD0, // Add address
    AD1, // Add address
}

// impl block with methods
impl<I2C, E> ICM42670P<I2C>
where
    // This defines which error messages will be used
    I2C: i2c::WriteRead<Error = E> + i2c::Write<Error = E>,
{
    /// Creates a new instance of the sensor, taking ownership of the i2c peripheral.
    pub fn new(i2c: I2C, address: DeviceAddr) -> Result<Self, E> {
        // Instantiates the ICM42670P struct
        // Returns the struct as Ok value
        todo!();
    }

    /// Returns the device's ID `0x67
    //(if it doesn't, something is amiss)
    // Public method that can be accessed from outside this file.
    pub fn read_device_id_register(&mut self) -> Result<u8, E> {
        // Reads the Device ID register
        todo!();
    }

    /// Writes into a register
    // This method is not public as it is only needed inside this file.
    #[allow(unused)]
    fn write_register(&mut self, register: Register, value: u8) -> Result<(), E> {
        // Value that will be written as u8
        // i2c write
        todo!();
    }

    /// Reads a register using a `write_read` method.
    // This method is not public as it is only needed inside this file.
    fn read_register(&mut self, register: Register) -> Result<u8, E> {
        // Buffer for values
        // i2c write_read
        // Return u8 from le bytes
        todo!();
    }
}

// See Table 14.1 in documentation
/// This enum represents the device's registers
#[derive(Clone, Copy)]
pub enum Register {
    // WhoAmI Register
}

impl Register {
    fn address(&self) -> u8 {
        // Returns Register as u8
        todo!();
    }
}


icm42670p.rs

[package]
name = "i2c-driver"
version = "0.1.0"
authors = [
    "Sergio Gasquez <sergio.gasquez@gmail.com>",
    "Tanks Transfeld <tanks.transfeld@ferrous-systems.com>",
]
edition = "2021"
resolver = "2"

[profile.release]
opt-level = "s"

[profile.dev]
debug     = true # Symbols are nice and they don't increase the size on Flash
opt-level = "z"

[dependencies]
anyhow       = "=1.0.75"
embedded-hal = "=0.2.7"
esp-idf-svc  = "=0.47.3"

[build-dependencies]
embuild = "=0.31.4"
