/*
  Controls three servos with different easing settings
  https://wokwi.com/projects/360276061783595009
  by dlloydev, March 2023.

  ⚪ The green servo moves from 0 to 90 deg at 70 deg/s with linear motion.
  ⚪ The orange servo moves from 0 to 180 deg at 140 deg/s with sigmoid motion.
  ⚪ The purple servo moves from 45 to 135 deg at 180 deg/s with steep sigmoid motion.
*/

#include "pwmWrite.h"

const int servoPin1 = 18;
const int servoPin2 = 19;
const int servoPin3 = 21;

// units in degrees per second
float speed1 = 70.0;
float speed2 = 140.0;
float speed3 = 180.0;

// When easing constant (ke) < 1.0, return value is normalized, when 1.0, returns pulse width (μs)
// ke = 0.0 is linear, between 0.0 and 1.0 is tunable sigmoid, 1.0 is normal response
// Normalized Tunable Sigmoid: https://www.desmos.com/calculator/ejkcwglzd1
float ke1 = 0.0;
float ke2 = 0.6;
float ke3 = 0.8;

// go to position (degrees)
uint8_t pos1 = 90;
uint8_t pos2 = 180;
uint8_t pos3 = 135;

// duration of travel in ms is degrees to move / speed * 1000
float dur1 = 90.0 / speed1 * 1000.0;
float dur2 = 180.0 / speed2 * 1000.0;
float dur3 = 90.0 / speed3 * 1000.0;

uint32_t prevMs1, prevMs2, prevMs3;

Pwm pwm = Pwm();

void setup() {
  Serial.begin(115200);
  //pwm.attach(servoPin3);
  //pwm.attach(servoPin3, 6);
  //pwm.attach(servoPin3, 533, 2333);
  //pwm.attach(servoPin3, 522, 2222, 122.2, 0.2);
  //pwm.attach(servoPin3, 6, 566, 2466, 180.0, 0.6);
  //pwm.attach(servoPin3, 6, 477, 2477, 177.0, 0.7, true);
}

void loop() {
  uint32_t ms1 = millis();
  uint32_t ms2 = ms1;
  uint32_t ms3 = ms1;
  float ye1, ye2, ye3;

  if (ms1 - prevMs1 > dur1) {
    prevMs1 = ms1;
    pos1 = (pos1 == 0) ? 90 : 0;
  }
  if (ms2 - prevMs2 > dur2) {
    prevMs2 = ms2;
    pos2 = (pos2 == 0) ? 180 : 0;
  }
  if (ms3 - prevMs3 > dur3) {
    prevMs3 = ms3;
    pos3 = (pos3 == 45) ? 135 : 45;
  }
  ye1 = pwm.writeServo(servoPin1, pos1, speed1, ke1);
  ye2 = pwm.writeServo(servoPin2, pos2, speed2, ke2);
  ye3 = pwm.writeServo(servoPin3, pos3, speed3, ke3);
  Serial.print(ye1);
  Serial.print(",");
  Serial.print(ye2);
  Serial.print(",");
  Serial.println(ye3);
  delay(6);
  pwm.printDebug();
}

/*

  "serialMonitor": { "display": "plotter", "newline": "lf" },

  printf(" ch: %d\n", ch);
  printf(" config[2].pin: %d\n", config[2].pin);
  printf(" config[ch].pin: %d\n", config[ch].pin);
  printf(" config[2].speed: %1.2f\n", config[2].speed);
  printf(" config[ch].speed: %1.2f\n", config[ch].speed);
  printf(" config[2].ke: %1.2f\n", config[2].ke);
  printf(" config[ch].ke: %1.2f\n", config[ch].ke);
  printf(".pin: %d, chan: %d, .minUs: %d, .maxUs: %d, .speed: %1.2f. .ke: %1.2f, invert: %d\n", config[ch].pin, chan, config[ch].servoMinUs, config[ch].servoMaxUs, config[ch].speed, config[ch].ke, invert);

*/