#include <IRremote.h>
#include <LiquidCrystal.h>
unsigned long compteur=0;
unsigned long compteurbat = 0;
unsigned long compteurdegivr = 0;
int etatled;
int memoire=HIGH;
int v4v = 3;
int ventilateur = 4;
int turbine = 5;
int compresseur = 6;
//int led1_rouge = 4;
//int led_verte = 9;
float Tempconsigne =22.00;
unsigned long count=0;
int mode_chauffage;   
int mode_deshumid;   
int mode_clim;      
const int sonde_ambianceMin = 0 ;
const int sonde_ambianceMax = 1;
int sonde_ambiance;// entree analogique en A0
 #define PIN_RECEIVER 2   // Signal Pin of IR receiver
IRrecv receiver(PIN_RECEIVER);
LiquidCrystal lcd(12, 11, 10, 9, 8, 7);

void setup()
{
  lcd.begin(16, 2);
  lcd.setCursor(4, 0);
  lcd.print("Attente");
  lcd.setCursor(0, 1);
  lcd.print("pression touche?");
  receiver.enableIRIn(); // Start the receiver
  pinMode(mode_chauffage, OUTPUT); // choix 2
	pinMode(mode_deshumid , OUTPUT); // choix 1
	pinMode(mode_clim, OUTPUT);      // choix 3
	pinMode(compresseur, OUTPUT);// Sortie relais compresseur
	pinMode(turbine, OUTPUT);// Sortie turbine Int
	pinMode(ventilateur, OUTPUT);// Sortie ventilateur Ext
	pinMode(v4v, OUTPUT);// Sortie V4 Voies
}

void loop()
{
  // Checks received an IR signal
  if (receiver.decode()) {
    translateIR();
    receiver.resume();  // Receive the next value
  }
}

/*void lcdPrint(char* text)
{
  lcd.clear();
//  lcd.setCursor(0, 0);
  //lcd.print("Choix:");
  lcd.setCursor(4, 0);
  lcd.print(text);
 // lcd.print(" code: ");
 // lcd.print(receiver.decodedIRData.command);
}
*/
void translateIR()
{
   lcd.clear();
  // Takes command based on IR code received
  switch (receiver.decodedIRData.command) {
    case 162:
   // lcd.clear();
     lcd.begin(16, 2);
      lcd.setCursor(4, 0);
      lcd.print("ON/OFF");//programme();
      break;
    case 226:
      lcd.print("MENU");
      break;
    case 34:
      lcd.print("TEST");
      break;
    case 2:
      lcd.print("PLUS");
      break;
    case 194:
      lcd.print("BACK");
      break;
    case 224:
      lcd.print("PREV.");
      break;
    case 168:
      lcd.print("PLAY");
      break;
    case 144:
      lcd.print(" MODE DESHUMID");
      break;
    case 104:
      lcd.print("num: 0");
      break;
    case 152:
      lcd.print("MINUS");
      break;
    case 176:
      lcd.print("key: C");
      break;
    case 48:
      lcd.print("num: 1");
       digitalWrite(mode_deshumid , HIGH);
      digitalWrite(mode_deshumid , HIGH); 
      digitalWrite(mode_chauffage, LOW);
      digitalWrite(mode_clim, LOW); 
           digitalWrite(turbine, HIGH);// Demarrage de la ventilation interieure
           lcd.begin(16, 2);
           lcd.setCursor(3, 0);
           lcd.print("Turbine ");
           lcd.setCursor(3, 1);
           lcd.print("en marche");
       
           delay(500);
           
      break;
    case 24:
      lcd.print("num: 2");
      break;
    case 122:
      lcd.print("num: 3");
      break;
    case 16:
      lcd.print("num: 4");
      break;
    case 56:
      lcd.print("num: 5");
      break;
    case 90:
      lcd.print("num: 6");
      break;
    case 66:
      lcd.print("num: 7");
      break;
    case 74:
     lcd.print("num: 8");
      break;
    case 82:
      lcd.print("num: 9");
      break;
    default:
      lcd.clear();
      lcd.print(receiver.decodedIRData.command);
      lcd.print(" other button");
      
  }
  
}