// File : Cascade165.ino
//
// Version 1, 5 August 2021, by Koepel
//     Initial version.
// Version 2, 5 August 2021, by Koepel
//     Layout of the wiring made better.
// Version 3, 13 August 2021, by Koepel
//     Changed 'SCK' to 'clockPin'.
//
// Cascade of four 74HC165 shift-in registers.
// Only three pins are used on the Arduino board, to read 32 switches.
//
// Using the 74HC165 is safe, because a pulse to the Latch pin
// ('PL' on the 74HC165) will make a new start every time.
// In case of an error or a wrong clock pulse by noise,
// it synchronizes the data when inputs are read the next time.
//
// Based on:
//   (1)
//     Demo sketch to read from a 74HC165 input shift register
//     by Nick Gammon, https://www.gammon.com.au/forum/?id=11979
//   (2)
//     74HC165 Shift register input example
//     by Uri Shaked, https://wokwi.com/arduino/projects/306031380875182657
//
//
//TO INVERT OUTPUT THE 74HC165 Connected directly to UNO connect uno with Q7_N
//FOR CONNECTION INSIDE OF CHAIN USE Q7

const byte latchPinIn = 9;
const byte clockPin = 13;
const byte clock_enablePin = 8;
const byte dataPinIn = 12;


const byte latchPinOut = 6;
const byte dataPinOut = 5;

void setup ()
{
  //Serial.begin( 115200);
    pinMode( clock_enablePin, OUTPUT);   // clock signal, idle LOW
  digitalWrite (clock_enablePin, LOW);
 

  pinMode( clockPin, OUTPUT);   // clock signal, idle LOW
  digitalWrite (clockPin, LOW);
  pinMode( latchPinIn, OUTPUT);   // latch (copy input into registers), idle HIGH
  digitalWrite( latchPinIn, HIGH);
  pinMode( dataPinIn, INPUT);

  pinMode(latchPinOut, OUTPUT);
  digitalWrite( latchPinOut, HIGH);
  pinMode(dataPinOut, OUTPUT);

  
}

// The shiftIn() can not be used here, because the clock is set idle low
// and the shiftIn() makes the clock high to read a bit.
// The 74HC165 requires to read the bit first and then give a clock pulse.
//

uint8_t shiftIn74HC165(uint8_t _dataPin, uint8_t _clockPin, uint8_t bitOrder) {

  uint8_t value = 0;
  uint8_t i;
  for (i = 0; i < 8; ++i) {
    if (bitOrder == LSBFIRST)
      value |= digitalRead(_dataPin) << i;
    else
      value |= digitalRead(_dataPin) << (7 - i);
    digitalWrite(_clockPin, HIGH);
    digitalWrite(_clockPin, LOW);
  }
  return value;
}


void updateShiftRegister(word state_reg)
{
  digitalWrite(latchPinOut, LOW);
  shiftOut(dataPinOut, clockPin, MSBFIRST, state_reg >> 8);
  shiftOut(dataPinOut, clockPin, MSBFIRST, state_reg >> 0);
  digitalWrite(latchPinOut, HIGH);
}

word readShiftRegister()
{
  // Give a pulse to the parallel load latch of all 74HC165
  digitalWrite( latchPinIn, LOW);
  digitalWrite( latchPinIn, HIGH);

  // Reading one 74HC165 at a time and combining them into a 32 bit variable
  // The last 74HC165 is at the bottom, but the switches start numbering
  // at the top. So the first byte has to be shifted into the highest place.

    word inreg = shiftIn74HC165(dataPinIn, clockPin, MSBFIRST);
    inreg |= shiftIn74HC165(dataPinIn, clockPin, MSBFIRST) << 8;

    return inreg;
}


void loop()
{

  word _state = readShiftRegister();

  updateShiftRegister(_state);


  /*Serial.print(millis());
  Serial.print(" : ");
  Serial.println(_state, BIN);*/
}