#include "stm32f1xx_hal.h"

#define LED_PORT                GPIOA
#define LED_PIN                 GPIO_PIN_6

#define LED_PORT_CLK_ENABLE     __HAL_RCC_GPIOA_CLK_ENABLE

UART_HandleTypeDef huart2;

void Error_Handler(void);
void SystemClock_Config(void);
static void MX_USART2_UART_Init(void);
/*void SysTick_Handler(void)
{
  HAL_IncTick();

  // 1 Hz blinking
  if ((HAL_GetTick() % 500) == 0) {
    HAL_GPIO_TogglePin(LED_PORT, LED_PIN);
  }
}*/

void initGPIO()
{
  GPIO_InitTypeDef GPIO_Config;
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_6, GPIO_PIN_RESET);
  GPIO_Config.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_Config.Pull = GPIO_NOPULL;
  GPIO_Config.Speed = GPIO_SPEED_FREQ_HIGH;

  GPIO_Config.Pin = LED_PIN;

  LED_PORT_CLK_ENABLE();
  HAL_GPIO_Init(LED_PORT, &GPIO_Config);

  __HAL_RCC_GPIOA_CLK_ENABLE();
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_6, GPIO_PIN_RESET);

  /*Configure GPIO pin : PA8 */
  GPIO_InitStruct.Pin = GPIO_PIN_6;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
 
}


int main(void)
{
  
  HAL_Init();

  HAL_IncTick();
  SystemClock_Config();
  initGPIO();
   while (1)
  {
      // LED ON
      HAL_GPIO_WritePin(GPIOA, GPIO_PIN_6, GPIO_PIN_SET);
      HAL_Delay(100);
      // LED OFF
      HAL_GPIO_WritePin(GPIOA, GPIO_PIN_6, GPIO_PIN_RESET);
      HAL_Delay(100);
  }
}


void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /* Initializes the CPU, AHB and APB busses clocks */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;

  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
    Error_Handler();
  }

  /* Initializes the CPU, AHB and APB busses clocks */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
                                | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK) {
    Error_Handler();
  }
}
static void MX_USART2_UART_Init(void)
{
  huart2.Instance = USART2;
  huart2.Init.BaudRate = 115200;
  huart2.Init.WordLength = UART_WORDLENGTH_8B;
  huart2.Init.StopBits = UART_STOPBITS_1;
  huart2.Init.Parity = UART_PARITY_NONE;
  huart2.Init.Mode = UART_MODE_TX_RX;
  huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart2.Init.OverSampling = UART_OVERSAMPLING_16;

  if (HAL_UART_Init(&huart2) != HAL_OK) {
    Error_Handler();
  }
}

#define STDOUT_FILENO   1
#define STDERR_FILENO   2

int _write(int file, char *ptr, int len)
{
  switch (file)
  {
    case STDOUT_FILENO: /*stdout*/
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      // Send the string somewhere
      break;
    case STDERR_FILENO: /* stderr */
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      // Send the string somewhere
      break;
    default:
      return -1;
  }
  return len;
}

void Error_Handler(void)
{
  /* User can add his own implementation to report the HAL error return state */
}

#ifdef USE_FULL_ASSERT
/**
    @brief  Reports the name of the source file and the source line number
            where the assert_param error has occurred.
    @param  file: pointer to the source file name
    @param  line: assert_param error line source number
    @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
    tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
}
#endif /* USE_FULL_ASSERT */