/*e--minning set rtc with menu */
//--LCD I2C
int h = 0;
int m = 0;
int d = 0;
//---LCD I2C
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27, 20, 4);
//---Gyroscope
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Wire.h>
Adafruit_MPU6050 mpu;
//---RTC Module
#include "RTClib.h"
RTC_DS1307 rtc;
char Day[7][12] = {"Minggu", "Senin", "Selasa", "Rabu", "Kamis", "Jumat", "Sabtu"};
String hari;
int tanggal, bulan, tahun, jam, menit, detik;
int pjam,sjam,pmenit,smenit,pdetik,sdetik;
int ptgl,stgl,pbln,sbln,pth,sth;
char kursor;
//---Button Menu
#define BUP 19
#define BOK 18
#define BDN 17
#define PUSH LOW //Ditekan
#define BOUN 20 //Bouncing
//---Sensor DHT
#include "DHT.h"
#define DHTPIN 23
#define DHTTYPE DHT22
DHT dht(DHTPIN, DHTTYPE);
float Temp, Hum;
//---Switch (Digital Input)
#define switch1 0 //Netral / WO Netral
#define switch2 2 //Power / Eco
#define switch3 4 //Brake
#define switch4 16 //Loading
#define switch5 15 //Loaded
#define switch6 12 //Dumping
#define switch7 13 //Empty
//---Output
#define relay1 27 //Netral | W/O Netral
#define relay2 14 //Power | Eco
//---Sensor (Analog Input)
#define analog1 34 //Speed
#define analog2 35 //Weight
#define analog3 32 //Front Suspension
#define analog4 33 //Rear Suspension
#define analog5 25 //Inclination
#define analog6 26 //Accel
int speeds = 70; //varieble to change speed
int an1, an2, an3, an4, an5, an6;
float gyroX, gyroY, gyroZ; //variable to save gyro
bool jalan,printSudut = true;
bool setMode = false;
//---Millis1 (Delay in Millisecond)
unsigned long previousMillis1 = 0;
const long Delay = 500;
//Kondisi
#define ON LOW //Kondisi ON
void setup() {
Serial.begin(115200);
jalan = false;
printSudut = false;
// LCD Init
lcd.init();
lcd.backlight();
//start dht and rtc
dht.begin();
rtc.begin();
pinMode(BUP, INPUT_PULLUP);
pinMode(BOK, INPUT_PULLUP);
pinMode(BDN, INPUT_PULLUP);
pinMode(relay1, OUTPUT);
pinMode(relay2, OUTPUT);
digitalWrite(relay1, LOW);
digitalWrite(relay2, LOW);
lcd.setCursor(0, 0); lcd.print(" SMART e-MINNING");
lcd.setCursor(0, 2); lcd.print(" PT. KARYA MULTI");
lcd.setCursor(0, 3); lcd.print(" SOLUTION INDONESIA");
delay(1000);
lcd.clear();
RealTime();
delay(2000);
lcd.clear();
// Gyro Init
while (!mpu.begin(0x69))
{
Serial.println("MPU6050 not connected!");
delay(1000);
}
Serial.println("MPU6050 ready!");
// RTC Init
if (! rtc.begin())
{
Serial.println("Couldn't find RTC");
Serial.flush();
abort();
}
}
// Declare sensor event to get readings
sensors_event_t event;
void loop() {
logic();
unsigned long currentMillis = millis();
if(currentMillis - previousMillis1 >= Delay){
previousMillis1 = currentMillis;
Analog_Input();
Digital_Input();
lcd.setCursor(0,0); lcd.print("Status:");
lcd.setCursor(0,1); lcd.print("Spd:"); lcd.print(an1); lcd.print("km "); //Machine Speed
lcd.setCursor(11,1); lcd.print("Load: "); lcd.print(an2,1); lcd.print("t "); //Live Weight
lcd.setCursor(0,2); lcd.print("Sus:"); lcd.print(an3); lcd.print(" "); //Suspension Front
lcd.setCursor(7,2); lcd.print("/"); lcd.print(an4); lcd.print(" "); //Suspension Rear
lcd.setCursor(12,2); lcd.print("Inc:"); lcd.print(an5); lcd.print("% "); //Inclination
lcd.setCursor(0,3); lcd.print("Shift(Ntr/WO) : ");
}
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
setMenu();
}
}
void RealTime(){
if (setMode) {
DateTime newTime(tahun , bulan, tanggal, h, m, d);
rtc.adjust(newTime);
setMode = false;
lcd.clear();
lcd.setCursor(0, 0);
lcd.print("Waktu diset.");
delay(1000);
lcd.clear();
}
else{
DateTime now = rtc.now();
hari = Day[now.dayOfTheWeek()];
tanggal = now.day(), DEC;
bulan = now.month(), DEC;
tahun = now.year(), DEC;
jam = now.hour(), DEC;
menit = now.minute(),DEC;
detik = now.second(),DEC;
lcd.setCursor(2,0);
lcd.print(String() +hari+ ", " +tanggal+ "-" +bulan+ "-" +tahun);
lcd.setCursor(6,1);
lcd.print(String() +jam+ ":" +menit+ ":" +detik);
lcd.setCursor(0,2);
lcd.print("--------------------");
lcd.setCursor(0,3);
lcd.print(" SEMANGAT PAGI !!!");}
}
void Analog_Input(){
//---Machine Speed
int sensor1 = analogRead(analog1);
an1 = map(sensor1, 0, 4095, 0, speeds);
//---Live Weight
int sensor2 = analogRead(analog2);
an2 = map(sensor2, 0, 4095, 0, 90);
//---Suspension Front
int sensor3 = analogRead(analog3);
an3 = map(sensor3, 0, 4095, 0, 300);
//---Suspension Rear
int sensor4 = analogRead(analog4);
an4 = map(sensor4, 0, 4095, 0, 300);
//---Inclination
int sensor5 = analogRead(analog5);
an5 = map(sensor5, 0, 4095, -10, 10);
//---Accel
int sensor6 = analogRead(analog6);
an6 = map(sensor6, 0, 4095, 0, 50);
}
void Digital_Input(){
//---Switch Netral / WO
if(digitalRead(switch1) == ON){
lcd.setCursor(17,3); lcd.print("NTR");
digitalWrite(relay1, HIGH);
} else {
lcd.setCursor(17,3); lcd.print("WO ");
digitalWrite(relay1, LOW);
}
//---Brake
if(digitalRead(switch3) == ON){
lcd.clear();
lcd.setCursor(0,2); lcd.print(" Brake Activated !!");
delay(2000);
lcd.clear();
}
//---Loading Mode Selector
if(digitalRead(switch4) == ON){
lcd.setCursor(8,0); lcd.print("LOADING ");
}
//---Loaded Mode Selector
if(digitalRead(switch5) == ON){
lcd.setCursor(8,0); lcd.print("LOADED ");
}
//---Dumping Mode Selector
if(digitalRead(switch6) == ON){
lcd.setCursor(8,0); lcd.print("DUMPING ");
}
//---Empty Mode Selector
if(digitalRead(switch7) == ON){
lcd.setCursor(8,0); lcd.print("EMPTY ");
}
}
void Temperature(){
unsigned long currentMillis = millis();
if(currentMillis - previousMillis1 >= Delay){
previousMillis1 = currentMillis;
Temp = random(0,50);//dht.readTemperature();
Hum = random(60,90);//dht.readHumidity();
lcd.setCursor(0, 0); lcd.print("Temperature Cabin :");
lcd.setCursor(0, 2); lcd.print("Temperature : "); lcd.print(Temp,1); lcd.print((char)223);lcd.print("C ");
lcd.setCursor(0, 3); lcd.print("Humidity : "); lcd.print(Hum,1); lcd.print("% ");
}
}
void setMenu(){
//---Set Menu 1
setMenu1:
if(digitalRead(BOK) == PUSH){ //OK || BACK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU1;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setExit;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu2;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. Date/Time <-");
lcd.setCursor(0, 1); lcd.print("02. Cabin Temp. ");
lcd.setCursor(0, 2); lcd.print("03. Monitor 2 ");
lcd.setCursor(0, 3); lcd.print("04. Monitor 3 ");
goto setMenu1;
//---Set Menu 2
setMenu2:
if(digitalRead(BOK) == LOW){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU2;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu1;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu3;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. Date/Time ");
lcd.setCursor(0, 1); lcd.print("02. Cabin Temp. <-");
lcd.setCursor(0, 2); lcd.print("03. Monitor 2 ");
lcd.setCursor(0, 3); lcd.print("04. Monitor 3 ");
goto setMenu2;
//---Set Menu 3
setMenu3:
if(digitalRead(BOK) == LOW){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU3;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu2;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu4;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. Date/Time ");
lcd.setCursor(0, 1); lcd.print("02. Cabin Temp. ");
lcd.setCursor(0, 2); lcd.print("03. Monitor 2 <-");
lcd.setCursor(0, 3); lcd.print("04. Monitor 3 ");
goto setMenu3;
//---Set Menu 4
setMenu4:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU4;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu3;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu5;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. Date/Time ");
lcd.setCursor(0, 1); lcd.print("02. Cabin Temp. ");
lcd.setCursor(0, 2); lcd.print("03. Monitor 2 ");
lcd.setCursor(0, 3); lcd.print("04. Monitor 3 <-");
goto setMenu4;
//---Set Menu 5
setMenu5:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU5;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu4;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu6;
}
logic();
lcd.setCursor(0, 0); lcd.print("05. Monitor 4 <-");
lcd.setCursor(0, 1); lcd.print("06. Gyro ");
lcd.setCursor(0, 2); lcd.print("07. SetTime ");
lcd.setCursor(0, 3); lcd.print("08. About ");
goto setMenu5;
//---Set Menu 6
setMenu6:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU6;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu5;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu7;
}
logic();
lcd.setCursor(0, 0); lcd.print("05. Monitor 4 ");
lcd.setCursor(0, 1); lcd.print("06. Gyro <-");
lcd.setCursor(0, 2); lcd.print("07. SetTime ");
lcd.setCursor(0, 3); lcd.print("08. About ");
goto setMenu6;
//--Set Menu 7
setMenu7:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU7;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu6;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu8;
}
logic();
lcd.setCursor(0, 0); lcd.print("05. Monitor 4 ");
lcd.setCursor(0, 1); lcd.print("06. Gyro ");
lcd.setCursor(0, 2); lcd.print("07. SetTime <-");
lcd.setCursor(0, 3); lcd.print("08. About ");
goto setMenu7;
//--Set Menu 8
setMenu8:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setSUBMENU8;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu7;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setExit;
}
logic();
lcd.setCursor(0, 0); lcd.print("05. Monitor 4 ");
lcd.setCursor(0, 1); lcd.print("06. Gyro ");
lcd.setCursor(0, 2); lcd.print("07. SetTime ");
lcd.setCursor(0, 3); lcd.print("08. About <-");
goto setMenu8;
//---Set jam
setJam:
if(digitalRead(BOK) == PUSH){ //OK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setPilihan1;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setBack;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenit;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. set jam <-");
lcd.setCursor(0, 1); lcd.print("02. set menit ");
lcd.setCursor(0, 2); lcd.print("03. set detik ");
lcd.setCursor(0, 3); lcd.print("04. set Time ");
goto setJam;
//----------------------------------------------------------------------------
//---Set Menit
setMenit:
if(digitalRead(BOK) == PUSH){ //OK || BACK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setPilihan2;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setJam;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setDetik;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. set jam ");
lcd.setCursor(0, 1); lcd.print("02. set menit <-");
lcd.setCursor(0, 2); lcd.print("03. set detik ");
lcd.setCursor(0, 3); lcd.print("04. set Time ");
goto setMenit;
//---Set detik
setDetik:
if(digitalRead(BOK) == PUSH){ //OK || BACK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setPilihan3;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenit;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setWaktu;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. set jam ");
lcd.setCursor(0, 1); lcd.print("02. set menit ");
lcd.setCursor(0, 2); lcd.print("03. set detik <-");
lcd.setCursor(0, 3); lcd.print("04. set Time ");
goto setDetik;
//---Set waktu
setWaktu:
if(digitalRead(BOK) == PUSH){ //OK || BACK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
setMode = !setMode;
goto setPilihan4;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setDetik;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setBack;
}
logic();
lcd.setCursor(0, 0); lcd.print("01. set jam ");
lcd.setCursor(0, 1); lcd.print("02. set menit ");
lcd.setCursor(0, 2); lcd.print("03. set detik ");
lcd.setCursor(0, 3); lcd.print("04. set Time <-");
goto setWaktu;
//---Set back
setBack:
if(digitalRead(BOK) == PUSH){ //OK || BACK
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu7;
}
else if(digitalRead(BUP) == PUSH){ //UP
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setWaktu;
}
else if(digitalRead(BDN) == PUSH){ //DOWN
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setJam;
}
logic();
lcd.setCursor(0, 0); lcd.print("05. set back <-");
goto setBack;
//---Exit Menu
setExit:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto endSET;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
goto setMenu8;
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
goto setMenu1;
}
logic();
lcd.setCursor(0, 0); lcd.print("09. Exit <-");
goto setExit;
//------------------SET WAKTU--------------------
//---pilihan 1
setPilihan1:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setJam;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
if (h==59) {h=0;}
else{h=h+1;}
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
if (h==0) {h=59;}
else{h=h-1;}
}
logic();
lcd.setCursor(0,0);
lcd.print("Set Hour:");
lcd.setCursor(9,0);
lcd.print(h,DEC);
goto setPilihan1;
//---pilihan 2
setPilihan2:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenit;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
lcd.clear();
if (m==59) {m=0;}
else{m=m+1;}
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
if (m==0) {m=59;}
else{m=m-1;}
}
logic();
lcd.setCursor(0,0);
lcd.print("Set Minutes:");
lcd.setCursor(12,0);
lcd.print(m,DEC);
goto setPilihan2;
setPilihan3:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setDetik;
}
else if(digitalRead(BUP) == PUSH){
delay(BOUN);
while(digitalRead(BUP) == PUSH){}
lcd.clear();
if (d==59) {d=0;}
else{d=d+1;}
}
else if(digitalRead(BDN) == PUSH){
delay(BOUN);
while(digitalRead(BDN) == PUSH){}
lcd.clear();
if (d==0) {d=59;}
else{
d=d-1;}
}
logic();
lcd.setCursor(0,0);
lcd.print("Set second:");
lcd.setCursor(11,0);
lcd.print(d,DEC);
goto setPilihan3;
setPilihan4:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setWaktu;
}
RealTime();
goto setPilihan4;
//------------------SET SUBMENU--------------------
//---Sub Menu 1
setSUBMENU1:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu1;
}
logic();
RealTime();
goto setSUBMENU1;
//---Sub Menu 2
setSUBMENU2:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu2;
}
logic();
Temperature();
goto setSUBMENU2;
//---Sub Menu 3
setSUBMENU3:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu3;
}
logic();
lcd.setCursor(0, 1); lcd.print("-> Sub3");
goto setSUBMENU3;
//---Sub Menu 4
setSUBMENU4:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu4;
}
logic();
lcd.setCursor(0, 1); lcd.print("-> Sub4");
goto setSUBMENU4;
//---Sub Menu 5
setSUBMENU5:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu5;
}
logic();
lcd.setCursor(0, 1); lcd.print("-> Sub5");
goto setSUBMENU5;
//---Sub Menu 6
setSUBMENU6:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu6;
}
printSudut = true;
//logic();
Gyroscope();
goto setSUBMENU6;
//---Sub Menu 7
setSUBMENU7:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu7;
}
logic();
goto setJam;
goto setSUBMENU7;
//---Sub Menu 8
setSUBMENU8:
if(digitalRead(BOK) == PUSH){
delay(BOUN);
while(digitalRead(BOK) == PUSH){}
lcd.clear();
goto setMenu8;
}
logic();
lcd.setCursor(0,0); lcd.print("Model : "); lcd.print("Trucker.ID");
lcd.setCursor(0,1); lcd.print("Version : "); lcd.print("v0.0.1");
lcd.setCursor(1,3); lcd.print("Made in Indonesia");
goto setSUBMENU8;
//---Back To Dashboard
endSET:
lcd.clear();
delay(100);
}
void logic(){
printSudut = false;
Gyroscope();
//---Gyro and max weight
if((an2 >= 90) && (gyroX >= 15.00)){
speeds = 70;// 100% of speeds
jalan = false;
digitalWrite(relay2, HIGH);// POWER IS ON
}
//---max weight and gyro (x,y) = 0
if((an2 >= 90) && ((gyroX == 0.00) && (gyroY == 0.00))){
speeds = 60;// 85% of 70km/h
jalan = true;
digitalWrite(relay2, LOW);// ECO IS ON
lcd.clear();
lcd.setCursor(3,0); lcd.print("MUATAN OVERLOAD");
lcd.setCursor(3,1); lcd.print("KURANGI MUATAN");
lcd.setCursor(3,2); lcd.print("LOADING ");
lcd.setCursor(3,3); lcd.print("DUMPING ");
delay(1000);
lcd.clear();
}
//---weightless
if(an2 == 0){
jalan = true;
digitalWrite(relay2, LOW);// ECO IS ON
}
//---Max Speed
if(an1 >= 65){
lcd.clear();
lcd.setCursor(5,1); lcd.print("OVER SPEED");
lcd.setCursor(2,2); lcd.print("KURANGI KECEPATAN");
delay(1000);
lcd.clear();
}
//---Gyro
//---Power / Eco
if(jalan){
if(digitalRead(switch2) == ON){
digitalWrite(relay2, HIGH);
} else {
digitalWrite(relay2, LOW);
}
}
//---Eco
//---Brake
//---Temperature
if(Temp >= 50){
lcd.clear();
lcd.setCursor(3,0); lcd.print("WARNING !!!");
lcd.setCursor(3,1); lcd.print("OVERHEAT");
lcd.setCursor(0,2); lcd.print("-------------------");
lcd.setCursor(0,3); lcd.print("CABIN TERLALU PANAS");
delay(1000);
lcd.clear();
}
Analog_Input();
//Serial.println(speeds);
}
void Gyroscope() {
//--Read MPU6050
sensors_event_t a, g, temp;
mpu.getEvent(&a, &g, &temp);
// Konversi kecepatan sudut gyroscope ke derajat/s
gyroX = g.gyro.x * 180.0 / PI;
gyroY = g.gyro.y * 180.0 / PI;
gyroZ = g.gyro.z * 180.0 / PI;
if(printSudut){
lcd.setCursor(0, 0);lcd.print("Kemiringan : ");
lcd.setCursor(0, 1);lcd.print("sumbu x : ");
lcd.setCursor(11, 1);lcd.print(gyroX,2);
lcd.setCursor(0, 2);lcd.print("sumbu y : ");
lcd.setCursor(11, 2);lcd.print(gyroY,2);
lcd.setCursor(0, 3);lcd.print("sumbu z : ");
lcd.setCursor(11, 3);lcd.print(gyroZ,2);
}
}