#include <EEPROM.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x27, 16, 2); // Set the LCD address to 0x27 for a 16 chars and 2 line display

long duration, inches;
int set_val;

//const int potPin = A1;         // Analog pin connected to the potentiometer
//const int potThreshold = 400;  // Threshold value for potentiometer indicating low flow
const int restartThreshold = 50; // Threshold value for restarting pump in automatic mode

const unsigned long debounceDelay = 50; // Debounce delay for switches

void setup() {
  Serial.begin(9600); // Initialize serial communication
  lcd.init();         // Initialize the LCD
  lcd.backlight();    // Turn on the backlight
  lcd.print("WATER LEVEL:");
  lcd.setCursor(0, 1);
  lcd.print("PUMP: OFF");

  //pinMode(3, OUTPUT);  // Added pinMode for pin 3
  pinMode(8, OUTPUT);
  pinMode(9, INPUT);
  pinMode(12, OUTPUT);
  //pinMode(potPin, INPUT); // Set potentiometer pin as input

  set_val = EEPROM.read(0);
  if (set_val > 150) set_val = 150;
}

void loop() {
  digitalWrite(3, LOW);
  delayMicroseconds(2);
  digitalWrite(8, HIGH);
  delayMicroseconds(10);
  digitalWrite(8, LOW);
  duration = pulseIn(9, HIGH);
  inches = microsecondsToInches(duration);

  int percentage = (set_val - inches) * 100 / set_val;

  lcd.setCursor(12, 0);
  if (percentage < 0) percentage = 0;
  lcd.print(percentage);
  lcd.print("%   ");

  bool pump = true; // Default to pump on

  // Dry run protection based on potentiometer
  //int potValue = analogRead(potPin);
  //Serial.print("Potentiometer value: ");
  //Serial.println(potValue); // Print potentiometer value for debugging

  //if (potValue < potThreshold) { // If potentiometer value indicates low flow
   // pump = false; // Stop the pump
    //lcd.setCursor(0, 1);
    //lcd.print("Dry run protection   ");
    //delay(2000); // Delay to show the message for 2 seconds
    //lcd.clear(); // Clear the LCD after displaying message
    //lcd.setCursor(0, 0); // Set cursor back to start
    //lcd.print("WATER LEVEL:"); // Reprint the label
  } if (percentage >= restartThreshold && percentage < 100) // Restart pump if water level falls below restart threshold and not at 100%
    pump = true;
    lcd.setCursor(0, 1);
    lcd.print("                    "); // Clear the line
  } else if (percentage >= 100) { // Turn off pump when water level reaches or exceeds 100 percent
    pump = false;
    lcd.setCursor(0, 1);
    lcd.print("Water level at 100% ");
    delay(2000); // Delay to show the message for 2 seconds
    lcd.clear(); // Clear the LCD after displaying message
    lcd.setCursor(0, 0); // Set cursor back to start
    lcd.print("WATER LEVEL:"); // Reprint the label
  }

  digitalWrite(12, !pump);

  // Debugging output for pump control
  Serial.print("Pump control: ");
  Serial.println(pump);

  lcd.setCursor(5, 1);
  if (pump)
    lcd.print("ON ");
  else
    lcd.print("OFF");

  delay(500);
}

long microsecondsToInches(long microseconds) {
  return microseconds / 74 / 2;
}