diagram.json

#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include <stm32c0xx_hal.h>

// ST Nucleo Green user LED (PA5)
#define LED_PORT                GPIOB
#define LED_PIN                 GPIO_PIN_6
#define LED_PORT_CLK_ENABLE     __HAL_RCC_GPIOB_CLK_ENABLE

UART_HandleTypeDef huart2;

void SystemClock_Config(void);
static void MX_USART2_UART_Init(void);

void osSystickHandler(void)
{
  // 1 Hz blinking:
  if ((HAL_GetTick() % 500) == 0)
  {
    HAL_GPIO_TogglePin(LED_PORT, LED_PIN);
  }
}

void initGPIO()
{
  GPIO_InitTypeDef GPIO_Config;

  GPIO_Config.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_Config.Pull = GPIO_NOPULL;
  GPIO_Config.Speed = GPIO_SPEED_FREQ_HIGH;

  GPIO_Config.Pin = LED_PIN;

  LED_PORT_CLK_ENABLE();
  HAL_GPIO_Init(LED_PORT, &GPIO_Config);

  LED_PORT_CLK_ENABLE();
}

int main(void)
{
  HAL_Init();
  SystemClock_Config();

  initGPIO();
  MX_USART2_UART_Init();

  printf("Hello, %s!\n", "Wokwi");

  HAL_GPIO_TogglePin(LED_PORT, LED_PIN);

  while (1);

  return 0;
}

/**
    @brief System Clock Configuration
    @retval None
*/
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
    in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSIDiv = RCC_HSI_DIV1;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
                                | RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
  {
    Error_Handler();
  }
}

/**
    @brief USART2 Initialization Function
    @param None
    @retval None
*/
static void MX_USART2_UART_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  __HAL_RCC_GPIOA_CLK_ENABLE();
  // PA2     ------> USART2_TX
  // PA3     ------> USART2_RX
  GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
  
  huart2.Instance = USART2;
  huart2.Init.BaudRate = 115200;
  huart2.Init.WordLength = UART_WORDLENGTH_8B;
  huart2.Init.StopBits = UART_STOPBITS_1;
  huart2.Init.Parity = UART_PARITY_NONE;
  huart2.Init.Mode = UART_MODE_TX_RX;
  huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart2.Init.OverSampling = UART_OVERSAMPLING_16;
  huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
  huart2.Init.ClockPrescaler = UART_PRESCALER_DIV1;
  huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  if (HAL_UART_Init(&huart2) != HAL_OK)
  {
    Error_Handler();
  }
}


void Error_Handler(void)
{
  /* User can add his own implementation to report the HAL error return state */
}


// The following makes printf() write to USART2:

#define STDOUT_FILENO   1
#define STDERR_FILENO   2

int _write(int file, uint8_t *ptr, int len)
{
  switch (file)
  {
    case STDOUT_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    case STDERR_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    default:
      return -1;
  }

  return len;
}
