// Source: NeoPixel Ring simple sketch (c) 2013 Shae Erisson
// Released under the GPLv3 license to match the rest of the
// Adafruit NeoPixel library

//####################################################################################################################
// This is sample code for Ampel - a WS2812 (Neopixel Stick) Traffic Light
// Based on a 3D printed housing together with a WS2812 LED Stick 
// 3D print files: https://www.printables.com/model/864750
// As I was not able to find a Neopixel Stick in WOKWI the scheme uses a Neopixel ring with the same number of LEDs

// Before connecting make sure to read and understand a more detailed instruction about 
// wiring and powering the LED stick. You can find it at: https://learn.adafruit.com/adafruit-neopixel-uberguide/powering-neopixels

// Disclaimer:
// Use at your own risk. This is an example only. I do not take any liability for damages or injuries.
// ###################################################################################################################
#include <Adafruit_NeoPixel.h>
#ifdef __AVR__
 #include <avr/power.h> // Required for 16 MHz Adafruit Trinket
#endif

// Which pin on the Arduino is connected to the NeoPixels?
#define PIN        6 // On Trinket or Gemma, suggest changing this to 1

// How many NeoPixels are attached to the Arduino?
#define NUMPIXELS 8 //  NeoPixel stick has 8 pixels 

// When setting up the NeoPixel library, we tell it how many pixels,
// and which pin to use to send signals. Note that for older NeoPixel
// strips you might need to change the third parameter -- see the
// strandtest example for more information on possible values.
Adafruit_NeoPixel pixels(NUMPIXELS, PIN, NEO_GRB + NEO_KHZ800);

#define DELAYVAL 1000 // Time (in milliseconds) to pause between pixels

void setup() {
  // These lines are specifically to support the Adafruit Trinket 5V 16 MHz.
  // Any other board, you can remove this part (but no harm leaving it):
#if defined(__AVR_ATtiny85__) && (F_CPU == 16000000)
  clock_prescale_set(clock_div_1);
#endif
  // END of Trinket-specific code.

  pixels.begin(); // INITIALIZE NeoPixel strip object (REQUIRED)
}

void loop() {
  pixels.clear(); // Set all pixel colors to 'off'
  pixels.setPixelColor(0, pixels.Color(255, 0, 0)); // Set pixel 0 to red 
  // pixels.setPixelColor(1, pixels.Color(255, 0, 0)); // Set pixel 1 to red 
  pixels.show();   // Send the updated pixel colors to the hardware.
  
  delay(DELAYVAL); // Pause before next step

  pixels.clear(); // Set all pixel colors to 'off'
  // pixels.setPixelColor(3, pixels.Color(255, 150, 0)); // Set pixel 3 to yellow 
  pixels.setPixelColor(4, pixels.Color(255, 150, 0)); // Set pixel 4 to yellow   
  pixels.show();   // Send the updated pixel colors to the hardware.
  delay(DELAYVAL); // Pause before next step

  pixels.clear(); // Set all pixel colors to 'off'
  // pixels.setPixelColor(6, pixels.Color(255, 150, 0)); // Set pixel 6 to green 
  pixels.setPixelColor(7, pixels.Color(0, 255, 0)); // Set pixel 7 to green 
  pixels.show();   // Send the updated pixel colors to the hardware.
  delay(DELAYVAL); // Pause before next pass through loop

 /* Color codes 

// RED = (255, 0, 0)
// YELLOW = (255, 150, 0)
// GREEN = (0, 255, 0) 
 */

  }