#include <Adafruit_Sensor.h>
#include <DHT_U.h>
#include <WiFi.h>
#include <PubSubClient.h>
#include <ESP32Servo.h> 
#include <FastLED.h> 
// Defining Pins
#define DHTPIN 12
#define LED 26
#define SERVO_PIN 2 // Servo motor pin
#define LED_PIN 4 
#define NUM_LEDS 16 // Number of LEDs in the strip

// DHT parameters
#define DHTTYPE    DHT22     // DHT 11
DHT_Unified dht(DHTPIN, DHTTYPE);
uint32_t delayMS;

// Servo motor
Servo servo;


CRGB leds[NUM_LEDS];

// MQTT Credentials
const char* ssid = "Wokwi-GUEST"; // Setting your AP SSID
const char* password = ""; // Setting your AP PSK
const char* mqttServer = "broker.hivemq.com";

const char* clientID = "ESP32-Wokwi"; //Random
const char* topic = "Tempdata"; 

// Parameters for using non-blocking delay
unsigned long previousMillis = 0;
const long interval = 1000;
String msgStr = "";      // MQTT message buffer
float temp, hum;

// Setting up WiFi and MQTT client
WiFiClient espClient;
PubSubClient client(espClient);

void setup_wifi() {
  delay(10);
  WiFi.begin(ssid, password);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.println("WiFi connected");
  Serial.println("IP address: ");
  Serial.println(WiFi.localIP());
}

void reconnect() {
  while (!client.connected()) {
    if (client.connect(clientID)) {
      Serial.println("MQTT connected");
      client.subscribe("lights");
      client.subscribe("servo"); // Subscribe to servo topic
      client.subscribe("lights/neopixel"); // Subscribe to neopixel topic
      Serial.println("Topic Subscribed");
    }
    else {
      Serial.print("failed, rc=");
      Serial.print(client.state());
      Serial.println(" try again in 5 seconds");
      delay(5000);  // wait 5sec and retry
    }
  }
}

// Subscribe callback
void callback(char* topic, byte* payload, unsigned int length) {
  Serial.print("Message arrived in topic: ");
  Serial.println(topic);
  Serial.print("Message: ");
  String data = "";
  for (int i = 0; i < length; i++) {
    Serial.print((char)payload[i]);
    data += (char)payload[i];
  }
  Serial.println();
  Serial.print("Message size: ");
  Serial.println(length);
  Serial.println();
  Serial.println("-----------------------");
  Serial.println(data);

  if (String(topic) == "lights") {
    if (data == "ON") {
      Serial.println("LED");
      digitalWrite(LED, HIGH);
    }
    else if(data=="OFF") {
      digitalWrite(LED, LOW);
    }
  }
  else if (String(topic) == "lights/neopixel") {
    if(data=="Flowering/ Budding"){
      Serial.println("Red");
      fill_solid(leds, NUM_LEDS, CRGB::Red); // Set all LEDs in the strip to the specified color
    FastLED.show(); // Update the LED strip with the new color
    }
    else if(data=="Larger leaves"){
      Serial.println("Dark red");
      fill_solid(leds, NUM_LEDS, CRGB::DarkRed); // Set all LEDs in the strip to the specified color
    FastLED.show(); // Update the LED strip with the new color
    }
    else if(data=="Growth of plant"){
      Serial.println("White");
      fill_solid(leds, NUM_LEDS, CRGB::White); // Set all LEDs in the strip to the specified color
    FastLED.show(); // Update the LED strip with the new color
    }
    else if(data=="Germination phase"){
      Serial.println("Blue");
      fill_solid(leds, NUM_LEDS, CRGB::Blue); // Set all LEDs in the strip to the specified color
    FastLED.show(); // Update the LED strip with the new color
    }
    else if(data=="Strong Stem"){
      Serial.println("Violet");
      fill_solid(leds, NUM_LEDS, CRGB(252, 9, 252)); // Set all LEDs in the strip to the specified color
    FastLED.show(); // Update the LED strip with the new color
    }
  }
  else if (String(topic) == "servo") {
    int degree = data.toInt(); // Convert the received data to an integer
    Serial.print("Moving servo to degree: ");
    Serial.println(degree);
    servo.write(degree); // Move the servo to the specified degree
  }
}

void setup() {
  Serial.begin(115200);
  dht.begin();
  // Get temperature sensor details.
  sensor_t sensor;
  dht.temperature().getSensor(&sensor);
  dht.humidity().getSensor(&sensor);
  pinMode(LED, OUTPUT);
  digitalWrite(LED, LOW);

  // Setup servo
  servo.attach(SERVO_PIN, 500, 2400);
  servo.write(0);

  // Setup WS2812 LED strip
  FastLED.addLeds<WS2812, LED_PIN, GRB>(leds, NUM_LEDS);

  setup_wifi();
  client.setServer(mqttServer, 1883); // Setting MQTT server
  client.setCallback(callback); // Define function which will be called when a message is received.
}

void loop() {
  if (!client.connected()) { // If client is not connected
    reconnect(); // Try to reconnect
  }
  client.loop();
  unsigned long currentMillis = millis(); // Read current time
  if (currentMillis - previousMillis >= interval) { // If current time - last time > 5 sec
    previousMillis = currentMillis;
    // Read temperature and humidity
    sensors_event_t event;
    dht.temperature().getEvent(&event);
    if (isnan(event.temperature)) {
      Serial.println(F("Error reading temperature!"));
    }
    else {
      Serial.print(F("Temperature: "));
      temp = event.temperature;
      Serial.print(temp);
      Serial.println(F("°C"));
    }
    // Get humidity event and print its value
    dht.humidity().getEvent(&event);
    if (isnan(event.relative_humidity)) {
      Serial.println(F("Error reading humidity!"));
    }
    else {
      Serial.print(F("Humidity: "));
      hum = event.relative_humidity;
      Serial.print(hum);
      Serial.println(F("%"));
    }
    msgStr = String(temp) + "," + String(hum) + ",";
    byte arrSize = msgStr.length() + 1;
    char msg[arrSize];
    Serial.print("PUBLISH DATA: ");
    Serial.println(msgStr);
    msgStr.toCharArray(msg, arrSize);
    client.publish(topic, msg);
    msgStr = "";
    delay(1);
    /*if (temp > 25 && hum > 60) {
    // Turn on LED ring
    servo.write(180); // Rotate to 180 degrees
  } else {
    // Turn off LED ring
    servo.write(0); // Rotate to 0 degrees
  }
  */
  }
}