#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include <stm32c0xx_hal.h>
#include "screen.h"
#include "ili9341.h"

// ST Nucleo Green user LED (PA5)
#define LED_PORT                GPIOB
#define LED_PIN                 GPIO_PIN_8
#define LED_PORT_CLK_ENABLE     __HAL_RCC_GPIOA_CLK_ENABLE

UART_HandleTypeDef huart2;
SPI_HandleTypeDef hspi1;

void SystemClock_Config(void);
static void MX_USART2_UART_Init(void);
static void MX_SPI1_Init(void);

void osSystickHandler(void)
{
  // 1 Hz blinking:
  if ((HAL_GetTick() % 500) == 0)
  {
    HAL_GPIO_TogglePin(LED_PORT, LED_PIN);
  }
}

void initGPIO() {
    GPIO_InitTypeDef GPIO_InitStruct = {0};

    // Enable the clock for SPI1
    __HAL_RCC_SPI1_CLK_ENABLE();

    // Enable GPIO clocks for GPIOA and GPIOB if needed
    __HAL_RCC_GPIOA_CLK_ENABLE();
    __HAL_RCC_GPIOB_CLK_ENABLE();

    // Configure SPI1 SCK (PA5), MISO (PA6), MOSI (PA7)
    GPIO_InitStruct.Pin = ILI9341_SCK_Pin | ILI9341_MISO_Pin | ILI9341_MOSI_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    GPIO_InitStruct.Alternate = GPIO_AF0_SPI1;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

    // Configure CS, RES, DC as output
    GPIO_InitStruct.Pin = ILI9341_CS_Pin | ILI9341_RES_Pin | ILI9341_DC_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

    // Configure LED pin
    GPIO_InitStruct.Pin = LED_PIN;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

    // Enable clock for the LED port and initialize the LED GPIO
    LED_PORT_CLK_ENABLE();
    HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
}


int main(void)
{
  HAL_Init();
  SystemClock_Config();

  initGPIO();
  MX_USART2_UART_Init();
  MX_SPI1_Init();
  
  ILI9341_Init();

  printf("Hello, %s!\n", "Wokwi");

  int i = 0;
  while (1){
    printf("Trying\n");
    ILI9341_DrawPixel(10, 10 + i++, 0xF800);
    HAL_Delay(100);
  }

  return 0;
}

/**
    @brief System Clock Configuration
    @retval None
*/
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
    in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSIDiv = RCC_HSI_DIV1;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
                                | RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
  {
    Error_Handler();
  }
}

/**
    @brief USART2 Initialization Function
    @param None
    @retval None
*/
static void MX_USART2_UART_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  __HAL_RCC_GPIOA_CLK_ENABLE();
  // PA2     ------> USART2_TX
  // PA3     ------> USART2_RX
  GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
  
  huart2.Instance = USART2;
  huart2.Init.BaudRate = 115200;
  huart2.Init.WordLength = UART_WORDLENGTH_8B;
  huart2.Init.StopBits = UART_STOPBITS_1;
  huart2.Init.Parity = UART_PARITY_NONE;
  huart2.Init.Mode = UART_MODE_TX_RX;
  huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart2.Init.OverSampling = UART_OVERSAMPLING_16;
  huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
  huart2.Init.ClockPrescaler = UART_PRESCALER_DIV1;
  huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  if (HAL_UART_Init(&huart2) != HAL_OK)
  {
    Error_Handler();
  }
}

static void MX_SPI1_Init(void)
{
  /* SPI1 parameter configuration*/
  hspi1.Instance = SPI1;
  hspi1.Init.Mode = SPI_MODE_MASTER;
  hspi1.Init.Direction = SPI_DIRECTION_2LINES;
  hspi1.Init.DataSize = SPI_DATASIZE_8BIT;
  hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
  hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
  hspi1.Init.NSS = SPI_NSS_SOFT;
  hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_64;
  hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;
  hspi1.Init.TIMode = SPI_TIMODE_DISABLE;
  hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
  hspi1.Init.CRCPolynomial = 10;
  if (HAL_SPI_Init(&hspi1) != HAL_OK)
  {
    Error_Handler();
  }

}


void Error_Handler(void)
{
  printf("Error");
  /* User can add his own implementation to report the HAL error return state */
}


// The following makes printf() write to USART2:

#define STDOUT_FILENO   1
#define STDERR_FILENO   2

int _write(int file, uint8_t *ptr, int len)
{
  switch (file)
  {
    case STDOUT_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    case STDERR_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    default:
      return -1;
  }

  return len;
}