#include <Arduino.h>
#include <Pushbutton.h>
#include <avr/sleep.h>
/*
   Specify which protocol(s) should be used for decoding.
   If no protocol is defined, all protocols (except Bang&Olufsen) are active.
   This must be done before the #include <IRremote.hpp>
*/

#define DECODE_NEC  // Includes Apple and Onkyo. To enable all protocols , just comment/disable this line.

//#define DECODE_FAST

//#define DECODE_DISTANCE_WIDTH // Universal decoder for pulse distance width protocols
//#define DECODE_HASH         // special decoder for all protocols

//#define DECODE_BEO          // This protocol must always be enabled manually, i.e. it is NOT enabled if no protocol is defined. It prevents decoding of SONY!

//#define DEBUG               // Activate this for lots of lovely debug output from the decoders.

//#define RAW_BUFFER_LENGTH  750 // For air condition remotes it requires 750. Default is 200.

/*
   This include defines the actual pin number for pins like IR_RECEIVE_PIN, IR_SEND_PIN for many different boards and architectures
*/
//#include "PinDefinitionsAndMore.h"
#include <IRremote.hpp>         // include the library

#define IR_RECEIVE_PIN 0
#define OUTPUT_PIN 4
int on = 0;
unsigned long last = millis();
int outPutValue = 0;

void setup() {
  // Serial.begin(115200);
  // while (!Serial)
  //   ;  // Wait for Serial to become available. Is optimized away for some cores.

  // // Just to know which program is running on my Arduino
  // Serial.println(F("START " __FILE__ " from " __DATE__ "\r\nUsing library version " VERSION_IRREMOTE));

  // Start the receiver and if not 3. parameter specified, take LED_BUILTIN pin from the internal boards definition as default feedback LED
  IrReceiver.begin(IR_RECEIVE_PIN, ENABLE_LED_FEEDBACK);

  // Serial.print(F("Ready to receive IR signals of protocols: "));
  // printActiveIRProtocols(&Serial);
  pinMode(OUTPUT_PIN, OUTPUT);


  //Serial.println(F("at pin " STR(IR_RECEIVE_PIN)));
}

void loop() {
  /*
       Check if received data is available and if yes, try to decode it.
       Decoded result is in the IrReceiver.decodedIRData structure.

       E.g. command is in IrReceiver.decodedIRData.command
       address is in command is in IrReceiver.decodedIRData.address
       and up to 32 bit raw data in IrReceiver.decodedIRData.decodedRawData
  */
  if (IrReceiver.decode()) {

    /*
           Print a summary of received data
    */
    if (IrReceiver.decodedIRData.protocol == UNKNOWN) {
      // Serial.println(F("Received noise or an unknown (or not yet enabled) protocol"));
      // // We have an unknown protocol here, print extended info
      // IrReceiver.printIRResultRawFormatted(&Serial, true);
      IrReceiver.resume();  // Do it here, to preserve raw data for printing with printIRResultRawFormatted()
    } else {
      IrReceiver.resume();  // Early enable receiving of the next IR frame
      // IrReceiver.printIRResultShort(&Serial);
      // IrReceiver.printIRSendUsage(&Serial);
    }
    //Serial.println();

    /*
           Finally, check the received data and perform actions according to the received command
    */
    if (IrReceiver.decodedIRData.command == 0x1) {
      if (millis() - last > 250) {
        on = !on;
        digitalWrite(OUTPUT_PIN, on ? HIGH : LOW);
      }
      last = millis();
    }
    IrReceiver.resume();
  }
}