/*
  MQUnifiedsensor Library - reading an MQ2

  Demonstrates the use a MQ2 sensor.
  Library originally added 01 may 2019
  by Miguel A Califa, Yersson Carrillo, Ghiordy Contreras, Mario Rodriguez
 
  Added example
  modified 23 May 2019
  by Miguel Califa 

  Updated library usage
  modified 26 March 2020
  by Miguel Califa 
  Wiring:
  https://github.com/miguel5612/MQSensorsLib_Docs/blob/master/static/img/MQ_Arduino.PNG
  Please make sure arduino A0 pin represents the analog input configured on #define pin

 This example code is in the public domain.

*/
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

//Include the library
#include <MQUnifiedsensor.h>
/************************Hardware Related Macros************************************/
#define         Board                   ("ESP-32")
#define         Pin                     (4)  //Analog input 3 of your arduino
/***********************Software Related Macros************************************/
#define         Type                    ("MQ-2") //MQ2
#define         Voltage_Resolution      (3.3)
#define         ADC_Bit_Resolution      (12) // For arduino UNO/MEGA/NANO
#define         RatioMQ2CleanAir        (9.83) //RS / R0 = 9.83 ppm 

/*****************************Globals***********************************************/
MQUnifiedsensor MQ2(Board, Voltage_Resolution, ADC_Bit_Resolution, Pin, Type);
/*****************************Globals***********************************************/
LiquidCrystal_I2C lcd(0x27, 16, 2);
int valor_gas = 0; 

void setup() {
  lcd.init();
  lcd.begin(16, 2);
  lcd.clear();
  lcd.backlight();
  lcd.print("PRACTICA");
  delay(1000);
   
  lcd.clear();
  lcd.print("SENSADO LM35");
  lcd.setCursor(0,1);
  lcd.print("CURSO 1 ");
  delay(1000);
  lcd.clear();
  //Init the serial port communication - to debug the library
  Serial.begin(9600); //Init serial port

  //Set math model to calculate the PPM concentration and the value of constants
  MQ2.setRegressionMethod(1); //_PPM =  a*ratio^b
  MQ2.setA(574.25); MQ2.setB(-2.222); // Configure the equation to to calculate LPG concentration
  /*
    Exponential regression:
    Gas    | a      | b
    H2     | 987.99 | -2.162
    LPG    | 574.25 | -2.222
    CO     | 36974  | -3.109
    Alcohol| 3616.1 | -2.675
    Propane| 658.71 | -2.168
  */

  /*****************************  MQ Init ********************************************/ 
  //Remarks: Configure the pin of arduino as input.
  /************************************************************************************/ 
  MQ2.init(); 
  /* 
    //If the RL value is different from 10K please assign your RL value with the following method:
    MQ2.setRL(10);
  */
  /*****************************  MQ CAlibration ********************************************/ 
  // Explanation: 
   // In this routine the sensor will measure the resistance of the sensor supposedly before being pre-heated
  // and on clean air (Calibration conditions), setting up R0 value.
  // We recomend executing this routine only on setup in laboratory conditions.
  // This routine does not need to be executed on each restart, you can load your R0 value from eeprom.
  // Acknowledgements: https://jayconsystems.com/blog/understanding-a-gas-sensor
  Serial.print("Calibrating please wait.");
  float calcR0 = 0;
  for(int i = 1; i<=10; i ++)
  {
    MQ2.update(); // Update data, the arduino will read the voltage from the analog pin
    calcR0 += MQ2.calibrate(RatioMQ2CleanAir);
    Serial.print(".");
  }
  MQ2.setR0(calcR0/10);
  Serial.println(calcR0);
  lcd.clear();
  lcd.setCursor(0,0);
  lcd.print("MQ2 = ");
  lcd.print(calcR0);
   delay(500); //Sampling frequency
  
  if(isinf(calcR0)) {Serial.println("Warning: Conection issue, R0 is infinite (Open circuit detected) please check your wiring and supply"); while(1);}
  if(calcR0 == 0){Serial.println("Warning: Conection issue found, R0 is zero (Analog pin shorts to ground) please check your wiring and supply"); while(1);}
  /*****************************  MQ CAlibration ********************************************/ 

  MQ2.serialDebug(true);
}

void loop() {
  MQ2.update(); // Update data, the arduino will read the voltage from the analog pin
  MQ2.readSensor(); // Sensor will read PPM concentration using the model, a and b values set previously or from the setup
  MQ2.serialDebug(); // Will print the table on the serial port
  //Serial.println(calcR0);
   valor_gas = analogRead(Pin);
   valor_gas = map(valor_gas, 0, 4095, 0, 100);
    Serial.println(valor_gas);
  lcd.clear();
  lcd.setCursor(0,0);
  lcd.print("MQ2 = ");
  lcd.print(valor_gas);
   delay(500); //Sampling frequency
}