/**
  ******************************************************************************
  * @file	: 01_DbncdMPBttn_1b.ino
  * @brief  : Example for the ButtonToSwitch_AVR library DbncdMPBttn class
  *
  * Repository: https://github.com/GabyGold67/ButtonToSwitch_AVR
  * WOKWI simulation URL: https://wokwi.com/projects/414291211763773441
  * 
  *   Framework: Arduino
  *   Platform: *
  * 
  * @details 
  * The example instantiates a DbncdMPBttn object using:
  * 	- 1 push button between GND and dmpbMainInpt
  * 	- 1 led with it's corresponding resistor between GND and dmpbIsOnOtpt
  * 	- 1 led with it's corresponding resistor between GND and dmpbIsEnabledOtpt
  *
  * This simple example instantiates the DbncdMPBttn object in the setup(),
  * and then checks it's attributes flags through the getters methods in the
  * loop().
  * 
  * When a change in the object's outputs attribute flags values is detected, it
  * manages the loads and resources that the switch turns On and Off, in this
  * example case are the output of some GPIO pins.
  * 
  * A time controlling code section changes the isEnabled attribute of the MPBttn
  * after a time period, changing the MPBttn from enabled to disabled and then
  * back, to test the MPBttn behavior when enabling and disabling the MPBttn
  * 
  * Note: The setIsOnDisabled() method affects the behavior of the MPBttn when it
  * enters the Disabled state, check the documentation and experiment with it.
  *
  * @author	: Gabriel D. Goldman
  * mail <[email protected]>
  * Github <https://github.com/GabyGold67>
  *
  * @date First release: 01/08/2023 
  *       Last update:   07/10/2024 14:20 GMT+0200 DST
  ******************************************************************************
  * @warning **Use of this library is under your own responsibility**
  * 
  * @warning The use of this library falls in the category described by The Alan 
  * Parsons Project (c) 1980 "Games People play" disclaimer:  
  * Games people play, you take it or you leave it  
  * Things that they say aren't alright  
  * If I promised you the moon and the stars, would you believe it?  
  * 
  * Released into the public domain in accordance with "GPL-3.0-or-later" license terms.
  ******************************************************************************
*/

#include <Arduino.h>
#include <ButtonToSwitch.h>

const uint8_t dmpbMainInpt{A0};
const uint8_t dmpbIsOnOtpt{3};
const uint8_t dmpbIsEnabledOtpt{4};

DbncdMPBttn myDMPBttn (dmpbMainInpt);

unsigned long int enbldOnOffTm{10000};
unsigned long int lstSwpTm{0};

void setup() {
  digitalWrite(dmpbIsOnOtpt, LOW);
  digitalWrite(dmpbIsEnabledOtpt, LOW);

  pinMode(dmpbIsOnOtpt, OUTPUT);
  pinMode(dmpbIsEnabledOtpt, OUTPUT);

  myDMPBttn.setIsOnDisabled(false);
  myDMPBttn.begin(40); 
}

void loop() {
  if((millis() - lstSwpTm) > enbldOnOffTm ){
    if(myDMPBttn.getIsEnabled() == true)
      myDMPBttn.disable();
    else
      myDMPBttn.enable();
    lstSwpTm = millis();
  }

  if(myDMPBttn.getOutputsChange()){ //This checking is done for saving resources, avoiding the rewriting of the pin value if there are no state changes in the MPB status
    digitalWrite(dmpbIsOnOtpt, (myDMPBttn.getIsOn())?HIGH:LOW);    
    digitalWrite(dmpbIsEnabledOtpt, (myDMPBttn.getIsEnabled())?LOW:HIGH);    
    myDMPBttn.setOutputsChange(false); //If the OutputChanges attibute flag is used, reset it's value to detect the next need to refresh outputs.
  }
}