//MSS-V6 11/28/24
//Nativ 1 Services
//Seedling Starter Controller
//Change to Current Time on Line 65.  Need to comment out and reload to keep current time


#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <Adafruit_Sensor.h>
#include <DHT.h>
#include <RTClib.h>
#include <OneWire.h>

#define SCREEN_WIDTH 128 // OLED display width, in pixels
#define SCREEN_HEIGHT 64 // OLED display height, in pixels

// Declaration for an SSD1306 display connected to I2C (SDA, SCL)   
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, -1);

// Pin definitions
const int Fan = 2; // Digital pin connected to the relay
const int TempSensor = 32; // Digital pin connected to the DHT sensor
const int Lights = 33; // Digital pin connected to lights

// Define Sensor
#define DHTTYPE DHT22

DHT dhtTemperature(TempSensor, DHTTYPE);

// RTC instance
RTC_DS3231 rtc;

// Global variables
unsigned long startTime = 0;
boolean lightState = false;
boolean fanState = false;
unsigned long fanStartTime = 0; // Variable to track fan start time

void setup() {
  Serial.begin(115200);

  dhtTemperature.begin();

  if (!display.begin(SSD1306_SWITCHCAPVCC, 0x3C)) {
    Serial.println(F("SSD1306 allocation failed"));
    for (;;);
  }
  delay(2000);
  display.clearDisplay();
  display.setTextColor(WHITE);

  // Initialize Pins
  pinMode(Fan, OUTPUT);
  pinMode(Lights, OUTPUT);

  // Initialize the RTC
  if (!rtc.begin()) {
    Serial.println("Couldn't find RTC");
    while (1) {} // Halt if RTC not found
  }
  //replace below wiht deisred time
  //rtc.adjust(DateTime(2024, 11, 29, 8, 47, 0)); // comment out this line after initial load and reload to keep time

}

void loop() {
  delay(5000);

  // Read temperature and humidity
  float tf = dhtTemperature.readTemperature();
  int hf = dhtTemperature.readHumidity(); // Convert humidity to int

  // Convert temperature to Fahrenheit
  float ff = tf * 1.8 + 32;

  if (isnan(ff) || isnan(tf) || isnan(hf)) {
    Serial.println("Failed to read from Temperature sensor!");
  }

  // Get current time
  DateTime now = rtc.now();

  // Control lights based on time
   if (now.hour() >= 6 && now.hour() < 18) {
    digitalWrite(Lights, HIGH);
    lightState = true;
   } else {
    digitalWrite(Lights, LOW);
    lightState = false;
   }

  // Control Fan based on time
   if (now.hour() >= 9 && now.hour() < 19) {
    digitalWrite(Fan, HIGH); // Activate relay
    fanState = true;
   } else {
    digitalWrite(Fan, LOW); // Deactivate relay
    fanState = false;
   }

 // Clear display
 display.clearDisplay();

 // Display Time
 display.setCursor(67,18);
 display.print(now.hour() % 11);
 display.print(":");
 display.print(now.minute() < 10 ? "0" : ""); // Print "0" if minutes are less than 10
 display.print(now.minute(), DEC);
 display.print(now.hour() >= 12 ? " PM" : " AM");

 // Display "New Beginnings"
 display.setTextSize(1);
 display.setCursor(0,25);
 display.print("New Beginnings");

 // Display Temperature
 display.setTextSize(1.75);
 display.setCursor(0, 35);
 display.print("Temp: ");
 display.setTextSize(1.75);
 display.setCursor(29, 35);
 display.print(int(ff));
 display.print(" ");
 display.setTextSize(1.75);
 display.cp437(true);
 display.write(167);
 display.setTextSize(1.75);
 display.print("F");

 // Display Humidity
 display.setTextSize(1.75);
 display.setCursor(0, 45);
 display.print("Humidity: ");
 display.setTextSize(1.75);
 display.setCursor(55, 45);
 display.print(hf);
 display.print("%");

 // Display Fan Status
 display.setTextSize(1.75);
 display.setCursor(0, 55); 
 display.print("Fan: ");
 display.setTextSize(1.75);
 display.setCursor(25, 55); 
 display.print(fanState ? "ON" : "OFF");

 // Display Light Status
 display.setTextSize(1.75);
 display.setCursor(50, 55);
 display.print("Lts: ");
 display.setTextSize(1.75);
 display.setCursor(80, 55); 
 display.print(lightState ? "ON" : "OFF");

 display.display();

 // Print temperature and humidity to serial monitor
 Serial.print("Temperature: ");
 Serial.print(int(ff)); // Print temperature without decimals
 Serial.println("%");
 Serial.print("   Humidity: ");
 Serial.print(hf);
 Serial.println("%");
}