#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include <stm32c0xx_hal.h>


UART_HandleTypeDef huart2;

void SystemClock_Config(void);
static void MX_USART2_UART_Init(void);

void initGPIO()
{
    GPIO_InitTypeDef GPIO_InitStruct;

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOA_CLK_ENABLE();
  __HAL_RCC_GPIOB_CLK_ENABLE();

  GPIO_InitStruct.Pin = GPIO_PIN_1;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /*GPIO_InitStruct.Pin = GPIO_PIN_4;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);*/

}

int main(void)
{
  HAL_Init();
  SystemClock_Config();

  initGPIO();
  MX_USART2_UART_Init();


  char receivedBuffer[20];
  int idx = 0;
  printf("Commands:\n");
  printf("ReleON\n");
  printf("ReleOFF\n");

  while (1)
  {
	  if (HAL_UART_Receive(&huart2, (uint8_t *)&receivedBuffer[idx], 1, HAL_MAX_DELAY) == HAL_OK) {

	        if (receivedBuffer[idx] == '\n' || receivedBuffer[idx] == '\r' || idx >= (sizeof(receivedBuffer) - 1)) {
	          receivedBuffer[idx] = '\0';
	          idx = 0;

	          if (strcmp(receivedBuffer, "ReleON") == 0) {
	            HAL_GPIO_WritePin(GPIOA, GPIO_PIN_1, GPIO_PIN_SET);
	            printf("Rele ON\n");
	          } else if (strcmp(receivedBuffer, "ReleOFF") == 0) {
	            HAL_GPIO_WritePin(GPIOA, GPIO_PIN_1, GPIO_PIN_RESET);
	            printf("Rele OFF\n");
	          }

	          memset(receivedBuffer, 0, sizeof(receivedBuffer));
	        } else {
	          idx++;
	        }
	      }
  }

  return 0;
}

void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
    in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSIDiv = RCC_HSI_DIV1;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
                                | RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
  {
    Error_Handler();
  }
}

static void MX_USART2_UART_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  __HAL_RCC_GPIOA_CLK_ENABLE();
  // PA2     ------> USART2_TX
  // PA3     ------> USART2_RX
  GPIO_InitStruct.Pin = GPIO_PIN_2 | GPIO_PIN_3;
  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  huart2.Instance = USART2;
  huart2.Init.BaudRate = 115200;
  huart2.Init.WordLength = UART_WORDLENGTH_8B;
  huart2.Init.StopBits = UART_STOPBITS_1;
  huart2.Init.Parity = UART_PARITY_NONE;
  huart2.Init.Mode = UART_MODE_TX_RX;
  huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart2.Init.OverSampling = UART_OVERSAMPLING_16;
  huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
  huart2.Init.ClockPrescaler = UART_PRESCALER_DIV1;
  huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  if (HAL_UART_Init(&huart2) != HAL_OK)
  {
    Error_Handler();
  }
}


void Error_Handler(void)
{
  /* User can add his own implementation to report the HAL error return state */
}


// The following makes printf() write to USART2:

#define STDOUT_FILENO   1
#define STDERR_FILENO   2

int _write(int file, uint8_t *ptr, int len)
{
  switch (file)
  {
    case STDOUT_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    case STDERR_FILENO:
      HAL_UART_Transmit(&huart2, ptr, len, HAL_MAX_DELAY);
      break;

    default:
      return -1;
  }

  return len;
}