#include <Arduino.h>
#include <EEPROM.h>
#include "Variables.h"

void setup() {
  Serial.begin(115200);
  Serial.println("Start");
  // set buttons as input
  for(int8_t i = 10; i>= 6; i--){
    Serial.println(i);
    delay(500);
  }
  pinMode(BUTTON1, INPUT_PULLUP);
  pinMode(BUTTON2, INPUT_PULLUP);
  pinMode(BUTTON3, INPUT_PULLUP);
  pinMode(BUTTON4, INPUT_PULLUP);
  pinMode(BUTTON5, INPUT_PULLUP);

  // set relays as output
  pinMode(RELAY1_PIN, OUTPUT);
  pinMode(RELAY2_PIN, OUTPUT);
  pinMode(RELAY3_PIN, OUTPUT);
  pinMode(RELAY4_PIN, OUTPUT);
  pinMode(RELAY5_PIN, OUTPUT);

  // set learn LED as output
  pinMode(LEARN_LED_PIN, OUTPUT);
}

void loop() {
  handleButtons();            // handle the button events including single press and both press detection
  if (learn_mode_enable) {    // check the learn mode status
    blinkLearnLED();          // start blink the learn LED
    if (program_slot == 0) {  // check the program slot last value, if the value is 0, then select the program slots depending on buttons status
      if (button1_pressed) {
        program_slot = 1;         // slot 1 is selected
        button1_pressed = false;  // reset button 1 is press status
      } else if (button2_pressed) {
        program_slot = 2;         // slot 2 is selected
        button2_pressed = false;  // reset button 2 is press status
      } else if (button3_pressed) {
        program_slot = 3;         // slot 3 is selected
        button3_pressed = false;  // reset button 3 is press status
      } else if (button4_pressed) {
        program_slot = 4;         // slot 4 is selected
        button4_pressed = false;  // reset button 4 is press status
      } else if (button5_pressed) {
        program_slot = 5;         // slot 5 is selected
        button5_pressed = false;  // reset button 5 is press status
      }
    } else {
      // check if both buttons (button 1 & button 3) is press
      if (both_button_pressed) {
        if (program_slot != 0) {
          saveRelayChanges(program_slot);  // save the last relays configuration
        }
        program_slot = 0;           // set the program slot value is 0
        learn_mode_enable = false;  // exit from the learn mode

        // set all relays status value is 0
        relay1_status = false;
        relay2_status = false;
        relay3_status = false;
        relay4_status = false;
        relay5_status = false;

        digitalWrite(LEARN_LED_PIN, LOW);  // turn off the learn LED
        both_button_pressed = false;       // reset the both button pressed status
      }

      // check the buttons individual status to set the relays status for save in the slot
      if (button1_pressed) {
        relay1_status = changeRelayState(RELAY1_PIN);  // change the relay 1 state value
        button1_pressed = false;
      } else if (button2_pressed) {
        relay2_status = changeRelayState(RELAY2_PIN);  // change the relay 2 state value
        button2_pressed = false;
      } else if (button3_pressed) {
        relay3_status = changeRelayState(RELAY3_PIN);  // change the relay 3 state value
        button3_pressed = false;
      } else if (button4_pressed) {
        relay4_status = changeRelayState(RELAY4_PIN);  // change the relay 4 state value
        button4_pressed = false;
      } else if (button5_pressed) {
        relay5_status = changeRelayState(RELAY5_PIN);  // change the relay 5 state value
        button5_pressed = false;
      }
    }
    // check both button press
    if (both_button_pressed) {
      turnOffAll();
      digitalWrite(LEARN_LED_PIN, LOW);
      learn_mode_enable = false;
      both_button_pressed = false;
    }
  } else {
    // check again both button pressed
    if (both_button_pressed) {
      turnOffAll();
      learn_mode_enable = true;
      both_button_pressed = false;
    }
    // load relay configuration
    if (button1_pressed) {
      if (button1_slot_toggle) {
        turnOffAll();
        button1_slot_toggle = false;
        button2_slot_toggle = false;
        button3_slot_toggle = false;
        button4_slot_toggle = false;
        button5_slot_toggle = false;
      } else {
        loadRelayChanges(1);
        button1_slot_toggle = true;
      }
      button1_pressed = false;
    } else if (button2_pressed) {
      if (button2_slot_toggle) {
        turnOffAll();
        button1_slot_toggle = false;
        button2_slot_toggle = false;
        button3_slot_toggle = false;
        button4_slot_toggle = false;
        button5_slot_toggle = false;
      } else {
        loadRelayChanges(2);
        button2_slot_toggle = true;
      }
      button2_pressed = false;
    } else if (button3_pressed) {
      if (button3_slot_toggle) {
        turnOffAll();
        button1_slot_toggle = false;
        button2_slot_toggle = false;
        button3_slot_toggle = false;
        button4_slot_toggle = false;
        button5_slot_toggle = false;
      } else {
        loadRelayChanges(3);
        button3_slot_toggle = true;
      }
      button3_pressed = false;
    } else if (button4_pressed) {
      if (button4_slot_toggle) {
        turnOffAll();
        button1_slot_toggle = false;
        button2_slot_toggle = false;
        button3_slot_toggle = false;
        button4_slot_toggle = false;
        button5_slot_toggle = false;
      } else {
        loadRelayChanges(4);
        button4_slot_toggle = true;
      }
      button4_pressed = false;
    } else if (button5_pressed) {
      if (button5_slot_toggle) {
        turnOffAll();
        button1_slot_toggle = false;
        button2_slot_toggle = false;
        button3_slot_toggle = false;
        button4_slot_toggle = false;
        button5_slot_toggle = false;
      } else {
        loadRelayChanges(5);
        button5_slot_toggle = true;
      }
      button5_pressed = false;
    }
  }
}