/*Ajústalo como proyecto maestro, para se pueda conectar y comunicar automáticamente por medio de 
bluetooh con otro proyecto esclavo que no tiene los potenciómetros digitales y el vúmetro, solo
tiene los  6 encoder y la pantalla oled con las mismas conexiones y configuraciones. El objetivo
es que el proyecto maestro tenga todas las funciones y el proyecto esclavo: visualice los cambios
y los valores de los encoder del proyecto maestro, pero también, pueda modificar desde el 
proyecto esclavo los valores de los encoder del proyecto maestro. 
Genera el código del proyecto maestro y el código del proyecto esclavo*/
// =====================================================================================
// ===                          PROYECTO MAESTRO (CON BLUETOOTH)                     ===
// =====================================================================================

#include <Wire.h>
#include <SPI.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <ESP32Encoder.h>
#include <math.h>
#include <BluetoothSerial.h> // <-- LIBRERÍA BLUETOOTH

// --- CONFIGURACIÓN DE BLUETOOTH ---
BluetoothSerial SerialBT;
String btBuffer = ""; // Buffer para recibir datos

// --- CONFIGURACIÓN DE PANTALLA OLED (I2C) ---
#define SCREEN_WIDTH 128
#define SCREEN_HEIGHT 64
#define OLED_RESET -1
#define SCREEN_ADDRESS 0x3C
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);

// --- CONFIGURACIÓN DE ENCODERS ---
#define VOL_CLK_PIN 12 
#define VOL_DT_PIN  13 
#define GAIN_CLK_PIN 1 //TX
#define GAIN_DT_PIN  3 //RX 
#define HIGH_CLK_PIN 34 
#define HIGH_DT_PIN  35
#define MID_HIGH_CLK_PIN 32
#define MID_HIGH_DT_PIN  33
#define MID_LOW_CLK_PIN  25
#define MID_LOW_DT_PIN   26
#define LOW_CLK_PIN 27
#define LOW_DT_PIN  14 

// --- CONFIGURACIÓN DE POTENCIÓMETROS DIGITALES (SPI) ---
// Pines SPI: MOSI=23, MISO=19, SCK=18
#define VOL_CS_PIN      15
#define GAIN_CS_PIN     5 //CS/SS
#define HIGH_CS_PIN     17 //TX2
#define MID_HIGH_CS_PIN 16 //RX2
#define MID_LOW_CS_PIN  4
#define LOW_CS_PIN      2

// --- CONFIGURACIÓN DEL VÚMETRO ---
#define VOLTAGE_IN_L 36 // Canal Izquierdo (ADC1_CH0)
#define VOLTAGE_IN_R 39 // Canal Derecho (ADC1_CH3)
#define SAMPLES_AVG 64
#define ADC_MAX_VALUE 4095
#define ADC_REF_0DB 1106.0 // Valor ADC que corresponde a 0dB
#define DB_MIN -30.0
#define DB_MAX 11.4
#define PEAK_HOLD_MS 1500
#define PEAK_DECAY_RATE 0.35

// --- PARÁMETROS DE FUNCIONAMIENTO ---
#define DISPLAY_TIMEOUT_MS 3000
const int POT_MAX_STEPS = 255;
#define ENCODER_STEPS_PER_DB 2

// Rangos de Decibelios (dB) para los controles
const int VOL_MIN = -80, VOL_MAX = 10;
const int GAIN_MIN = -20, GAIN_MAX = 20;
const int EQ_MIN = -15, EQ_MAX = 15;

// --- OBJETOS GLOBALES ---
ESP32Encoder encoderVol;
ESP32Encoder encoderGain;
ESP32Encoder encoderHigh;
ESP32Encoder encoderMidHigh;
ESP32Encoder encoderMidLow;
ESP32Encoder encoderLow;

// --- VARIABLES DE ESTADO GLOBALES ---
int currentVolDB = 0;
int currentGainDB = 0;
int currentHighDB = 0;
int currentMidHighDB = 0;
int currentMidLowDB = 0;
int currentLowDB = 0;
double peakL = DB_MIN;
double peakR = DB_MIN;
unsigned long lastPeakTimeL = 0;
unsigned long lastPeakTimeR = 0;
enum DisplayMode { MODE_VUMETER, MODE_PARAM };
DisplayMode currentMode = MODE_VUMETER;
unsigned long lastInteractionTime = 0;

// --- PROTOTIPOS DE FUNCIONES ---
void writeToPot(int csPin, byte address, byte value);
void setPotValue(int csPin, int dbValue, int dbMin, int dbMax);
void actualizarPantallaParametro(const char *paramName, int currentValue, int minValue, int maxValue);
void drawVUMeterBar(int x_start, int y_start, double dbValue, double peakDbValue);
void actualizarVUMeter();
void handleBluetoothCommands(); // <-- NUEVA FUNCIÓN


// =====================================================================================
// ===                                   SETUP                                     ===
// =====================================================================================
void setup() {
  // --- Inicialización de Buses ---
  SPI.begin();
  Wire.begin();
  SerialBT.begin("PatroDJ_Master"); // <-- INICIAR BLUETOOTH CON NOMBRE

  // ... (El resto del setup es idéntico al original) ...
  pinMode(VOL_CS_PIN, OUTPUT);
  pinMode(GAIN_CS_PIN, OUTPUT);
  pinMode(HIGH_CS_PIN, OUTPUT);
  pinMode(MID_HIGH_CS_PIN, OUTPUT);
  pinMode(MID_LOW_CS_PIN, OUTPUT);
  pinMode(LOW_CS_PIN, OUTPUT);
  digitalWrite(VOL_CS_PIN, HIGH);
  digitalWrite(GAIN_CS_PIN, HIGH);
  digitalWrite(HIGH_CS_PIN, HIGH);
  digitalWrite(MID_HIGH_CS_PIN, HIGH);
  digitalWrite(MID_LOW_CS_PIN, HIGH);
  digitalWrite(LOW_CS_PIN, HIGH);

  encoderVol.attachHalfQuad(VOL_DT_PIN, VOL_CLK_PIN);
  encoderVol.setCount(VOL_MIN * ENCODER_STEPS_PER_DB);
  currentVolDB = VOL_MIN;
  encoderGain.attachHalfQuad(GAIN_DT_PIN, GAIN_CLK_PIN);
  encoderGain.setCount(0 * ENCODER_STEPS_PER_DB);
  encoderHigh.attachHalfQuad(HIGH_DT_PIN, HIGH_CLK_PIN);
  encoderHigh.setCount(0 * ENCODER_STEPS_PER_DB);
  encoderMidHigh.attachHalfQuad(MID_HIGH_DT_PIN, MID_HIGH_CLK_PIN);
  encoderMidHigh.setCount(0 * ENCODER_STEPS_PER_DB);
  encoderMidLow.attachHalfQuad(MID_LOW_DT_PIN, MID_LOW_CLK_PIN);
  encoderMidLow.setCount(0 * ENCODER_STEPS_PER_DB);
  encoderLow.attachHalfQuad(LOW_DT_PIN, LOW_CLK_PIN);
  encoderLow.setCount(0 * ENCODER_STEPS_PER_DB);
  
  setPotValue(VOL_CS_PIN, currentVolDB, VOL_MIN, VOL_MAX);
  setPotValue(GAIN_CS_PIN, currentGainDB, GAIN_MIN, GAIN_MAX);
  setPotValue(HIGH_CS_PIN, currentHighDB, EQ_MIN, EQ_MAX);
  setPotValue(MID_HIGH_CS_PIN, currentMidHighDB, EQ_MIN, EQ_MAX);
  setPotValue(MID_LOW_CS_PIN, currentMidLowDB, EQ_MIN, EQ_MAX);
  setPotValue(LOW_CS_PIN, currentLowDB, EQ_MIN, EQ_MAX);
  
  display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS);
  display.clearDisplay();
  display.setTextSize(2);
  display.setTextColor(SSD1306_WHITE);
  display.setCursor(15, 24);
  display.println("PATRO DJ");
  display.display();
  delay(1500);

  lastInteractionTime = millis();
  currentMode = MODE_VUMETER;
}


// =====================================================================================
// ===                                 MAIN LOOP                                   ===
// =====================================================================================
void loop() {
  bool interaction = false;

  // --- 0. PROCESAR COMANDOS ENTRANTES DE BLUETOOTH ---
  if (SerialBT.available()) {
    handleBluetoothCommands();
    interaction = true; // Un comando remoto cuenta como interacción
  }

  // --- 1. LEER ENCODERS LOCALES Y ACTUALIZAR PARÁMETROS ---
  long newVol = encoderVol.getCount() / ENCODER_STEPS_PER_DB;
  if (newVol > VOL_MAX) { newVol = VOL_MAX; encoderVol.setCount(newVol * ENCODER_STEPS_PER_DB); }
  if (newVol < VOL_MIN) { newVol = VOL_MIN; encoderVol.setCount(newVol * ENCODER_STEPS_PER_DB); }
  if (newVol != currentVolDB) {
    currentVolDB = newVol;
    actualizarPantallaParametro("VOLUMEN", currentVolDB, VOL_MIN, VOL_MAX);
    setPotValue(VOL_CS_PIN, currentVolDB, VOL_MIN, VOL_MAX);
    SerialBT.printf("V%d;", currentVolDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }

  long newGain = encoderGain.getCount() / ENCODER_STEPS_PER_DB;
  if (newGain > GAIN_MAX) { newGain = GAIN_MAX; encoderGain.setCount(newGain * ENCODER_STEPS_PER_DB); }
  if (newGain < GAIN_MIN) { newGain = GAIN_MIN; encoderGain.setCount(newGain * ENCODER_STEPS_PER_DB); }
  if (newGain != currentGainDB) {
    currentGainDB = newGain;
    actualizarPantallaParametro("GAIN", currentGainDB, GAIN_MIN, GAIN_MAX);
    setPotValue(GAIN_CS_PIN, currentGainDB, GAIN_MIN, GAIN_MAX);
    SerialBT.printf("G%d;", currentGainDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }

  long newHigh = encoderHigh.getCount() / ENCODER_STEPS_PER_DB;
  if (newHigh > EQ_MAX) { newHigh = EQ_MAX; encoderHigh.setCount(newHigh * ENCODER_STEPS_PER_DB); }
  if (newHigh < EQ_MIN) { newHigh = EQ_MIN; encoderHigh.setCount(newHigh * ENCODER_STEPS_PER_DB); }
  if (newHigh != currentHighDB) {
    currentHighDB = newHigh;
    actualizarPantallaParametro("HIGH", currentHighDB, EQ_MIN, EQ_MAX);
    setPotValue(HIGH_CS_PIN, currentHighDB, EQ_MIN, EQ_MAX);
    SerialBT.printf("H%d;", currentHighDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }
  
  long newMidHigh = encoderMidHigh.getCount() / ENCODER_STEPS_PER_DB;
  if (newMidHigh > EQ_MAX) { newMidHigh = EQ_MAX; encoderMidHigh.setCount(newMidHigh * ENCODER_STEPS_PER_DB); }
  if (newMidHigh < EQ_MIN) { newMidHigh = EQ_MIN; encoderMidHigh.setCount(newMidHigh * ENCODER_STEPS_PER_DB); }
  if (newMidHigh != currentMidHighDB) {
    currentMidHighDB = newMidHigh;
    actualizarPantallaParametro("MID HIGH", currentMidHighDB, EQ_MIN, EQ_MAX);
    setPotValue(MID_HIGH_CS_PIN, currentMidHighDB, EQ_MIN, EQ_MAX);
    SerialBT.printf("M%d;", currentMidHighDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }
  
  long newMidLow = encoderMidLow.getCount() / ENCODER_STEPS_PER_DB;
  if (newMidLow > EQ_MAX) { newMidLow = EQ_MAX; encoderMidLow.setCount(newMidLow * ENCODER_STEPS_PER_DB); }
  if (newMidLow < EQ_MIN) { newMidLow = EQ_MIN; encoderMidLow.setCount(newMidLow * ENCODER_STEPS_PER_DB); }
  if (newMidLow != currentMidLowDB) {
    currentMidLowDB = newMidLow;
    actualizarPantallaParametro("MID LOW", currentMidLowDB, EQ_MIN, EQ_MAX);
    setPotValue(MID_LOW_CS_PIN, currentMidLowDB, EQ_MIN, EQ_MAX);
    SerialBT.printf("N%d;", currentMidLowDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }

  long newLow = encoderLow.getCount() / ENCODER_STEPS_PER_DB;
  if (newLow > EQ_MAX) { newLow = EQ_MAX; encoderLow.setCount(newLow * ENCODER_STEPS_PER_DB); }
  if (newLow < EQ_MIN) { newLow = EQ_MIN; encoderLow.setCount(newLow * ENCODER_STEPS_PER_DB); }
  if (newLow != currentLowDB) {
    currentLowDB = newLow;
    actualizarPantallaParametro("LOW", currentLowDB, EQ_MIN, EQ_MAX);
    setPotValue(LOW_CS_PIN, currentLowDB, EQ_MIN, EQ_MAX);
    SerialBT.printf("L%d;", currentLowDB); // <-- ENVIAR CAMBIO POR BT
    interaction = true;
  }
  
  // --- 2. GESTIONAR EL MODO DE LA PANTALLA ---
  if (interaction) {
    lastInteractionTime = millis();
    currentMode = MODE_PARAM;
  } else {
    if (currentMode == MODE_PARAM && (millis() - lastInteractionTime > DISPLAY_TIMEOUT_MS)) {
      currentMode = MODE_VUMETER;
    }
  }

  // --- 3. DIBUJAR EN PANTALLA SEGÚN EL MODO ---
  if (currentMode == MODE_VUMETER) {
    actualizarVUMeter();
    delay(50);
  } else {
    delay(20);
  }
}

// =====================================================================================
// ===                      FUNCIONES DE COMUNICACIÓN BLUETOOTH                     ===
// =====================================================================================
void handleBluetoothCommands() {
    String message = SerialBT.readStringUntil(';');
    if (message.length() > 1) {
        char command = message.charAt(0);
        int value = message.substring(1).toInt();

        switch (command) {
            case 'V':
                currentVolDB = constrain(value, VOL_MIN, VOL_MAX);
                encoderVol.setCount(currentVolDB * ENCODER_STEPS_PER_DB);
                setPotValue(VOL_CS_PIN, currentVolDB, VOL_MIN, VOL_MAX);
                actualizarPantallaParametro("VOLUMEN", currentVolDB, VOL_MIN, VOL_MAX);
                break;
            case 'G':
                currentGainDB = constrain(value, GAIN_MIN, GAIN_MAX);
                encoderGain.setCount(currentGainDB * ENCODER_STEPS_PER_DB);
                setPotValue(GAIN_CS_PIN, currentGainDB, GAIN_MIN, GAIN_MAX);
                actualizarPantallaParametro("GAIN", currentGainDB, GAIN_MIN, GAIN_MAX);
                break;
            case 'H':
                currentHighDB = constrain(value, EQ_MIN, EQ_MAX);
                encoderHigh.setCount(currentHighDB * ENCODER_STEPS_PER_DB);
                setPotValue(HIGH_CS_PIN, currentHighDB, EQ_MIN, EQ_MAX);
                actualizarPantallaParametro("HIGH", currentHighDB, EQ_MIN, EQ_MAX);
                break;
            case 'M': // Mid High
                currentMidHighDB = constrain(value, EQ_MIN, EQ_MAX);
                encoderMidHigh.setCount(currentMidHighDB * ENCODER_STEPS_PER_DB);
                setPotValue(MID_HIGH_CS_PIN, currentMidHighDB, EQ_MIN, EQ_MAX);
                actualizarPantallaParametro("MID HIGH", currentMidHighDB, EQ_MIN, EQ_MAX);
                break;
            case 'N': // Mid Low
                currentMidLowDB = constrain(value, EQ_MIN, EQ_MAX);
                encoderMidLow.setCount(currentMidLowDB * ENCODER_STEPS_PER_DB);
                setPotValue(MID_LOW_CS_PIN, currentMidLowDB, EQ_MIN, EQ_MAX);
                actualizarPantallaParametro("MID LOW", currentMidLowDB, EQ_MIN, EQ_MAX);
                break;
            case 'L': // Low
                currentLowDB = constrain(value, EQ_MIN, EQ_MAX);
                encoderLow.setCount(currentLowDB * ENCODER_STEPS_PER_DB);
                setPotValue(LOW_CS_PIN, currentLowDB, EQ_MIN, EQ_MAX);
                actualizarPantallaParametro("LOW", currentLowDB, EQ_MIN, EQ_MAX);
                break;
        }
    }
}

// ... (El resto de funciones: writeToPot, setPotValue, actualizarPantallaParametro, drawVUMeterBar, actualizarVUMeter son idénticas al original) ...
void writeToPot(int csPin, byte address, byte value) {
  SPI.beginTransaction(SPISettings(1000000, MSBFIRST, SPI_MODE0));
  digitalWrite(csPin, LOW);
  SPI.transfer(address);
  SPI.transfer(value);
  digitalWrite(csPin, HIGH);
  SPI.endTransaction();
}
void setPotValue(int csPin, int dbValue, int dbMin, int dbMax) {
  long potStep = map(dbValue, dbMin, dbMax, POT_MAX_STEPS, 0); 
  potStep = constrain(potStep, 0, POT_MAX_STEPS);
  writeToPot(csPin, 0x00, (byte)potStep);
  writeToPot(csPin, 0x10, (byte)potStep);
}
void actualizarPantallaParametro(const char *paramName, int currentValue, int minValue, int maxValue) {
  display.clearDisplay();
  display.setTextSize(2);
  display.setTextColor(SSD1306_WHITE);
  int16_t x1, y1;
  uint16_t w, h;
  display.getTextBounds(paramName, 0, 0, &x1, &y1, &w, &h);
  display.setCursor((SCREEN_WIDTH - w) / 2, 2);
  display.println(paramName);
  char dbStr[10];
  sprintf(dbStr, "%+d dB", currentValue); 
  display.getTextBounds(dbStr, 0, 0, &x1, &y1, &w, &h);
  display.setCursor((SCREEN_WIDTH - w) / 2, 20);
  display.print(dbStr);
  int barWidth = map(currentValue, minValue, maxValue, 0, SCREEN_WIDTH);
  display.drawRect(0, 42, SCREEN_WIDTH, 16, SSD1306_WHITE);
  if (minValue < 0 && maxValue > 0) {
    int zeroPoint = map(0, minValue, maxValue, 0, SCREEN_WIDTH);
    display.drawFastVLine(zeroPoint, 40, 20, SSD1306_WHITE);
    if (barWidth > zeroPoint) {
      display.fillRect(zeroPoint, 42, barWidth - zeroPoint, 16, SSD1306_WHITE);
    } else {
      display.fillRect(barWidth, 42, zeroPoint - barWidth, 16, SSD1306_WHITE);
    }
  } else {
    display.fillRect(0, 42, barWidth, 16, SSD1306_WHITE);
  }
  display.display();
}
void drawVUMeterBar(int x_start, int y_start, double dbValue, double peakDbValue) {
  #define BAR_LENGTH 100
  #define BAR_HEIGHT 20
  #define SEGMENT_WIDTH 3
  #define SEGMENT_SPACING 1
  int totalSegments = BAR_LENGTH / (SEGMENT_WIDTH + SEGMENT_SPACING);
  display.drawRect(x_start - 1, y_start - 1, BAR_LENGTH + 2, BAR_HEIGHT + 2, SSD1306_WHITE);
  int activeSegments = map(dbValue, DB_MIN, DB_MAX, 0, totalSegments);
  activeSegments = constrain(activeSegments, 0, totalSegments);
  for (int i = 0; i < activeSegments; i++) {
    int xPos = x_start + (i * (SEGMENT_WIDTH + SEGMENT_SPACING));
    display.fillRect(xPos, y_start, SEGMENT_WIDTH, BAR_HEIGHT, SSD1306_WHITE);
  }
  int peakSegment = map(peakDbValue, DB_MIN, DB_MAX, 0, totalSegments);
  peakSegment = constrain(peakSegment, 0, totalSegments);
  int peakXPos = x_start + (peakSegment * (SEGMENT_WIDTH + SEGMENT_SPACING));
  if (peakXPos < x_start + BAR_LENGTH) {
    display.fillRect(peakXPos, y_start, SEGMENT_WIDTH, BAR_HEIGHT, SSD1306_WHITE);
  }
}
void actualizarVUMeter() {
  unsigned long totalL = 0;
  unsigned long totalR = 0;
  for (int i = 0; i < SAMPLES_AVG; i++) {
    totalL += analogRead(VOLTAGE_IN_L);
    totalR += analogRead(VOLTAGE_IN_R);
  }
  double dbL = (totalL == 0) ? DB_MIN : 20 * log10((double)(totalL / SAMPLES_AVG) / ADC_REF_0DB);
  double dbR = (totalR == 0) ? DB_MIN : 20 * log10((double)(totalR / SAMPLES_AVG) / ADC_REF_0DB);
  unsigned long currentTime = millis();
  if (dbL >= peakL) {
    peakL = dbL;
    lastPeakTimeL = currentTime;
  } else if (currentTime - lastPeakTimeL > PEAK_HOLD_MS) {
    peakL -= PEAK_DECAY_RATE;
    if (peakL < dbL) peakL = dbL;
    if (peakL < DB_MIN) peakL = DB_MIN;
  }
  if (dbR >= peakR) {
    peakR = dbR;
    lastPeakTimeR = currentTime;
  } else if (currentTime - lastPeakTimeR > PEAK_HOLD_MS) {
    peakR -= PEAK_DECAY_RATE;
    if (peakR < dbR) peakR = dbR;
    if (peakR < DB_MIN) peakR = DB_MIN;
  }
  display.clearDisplay();
  int label_x = 9;
  int bar_x_start = 26;
  display.setTextSize(1);
  display.setTextColor(SSD1306_WHITE);
  drawVUMeterBar(bar_x_start, 4, dbL, peakL); 
  display.setCursor(1, 12);
  int roundedDbL = round(dbL); 
  if (roundedDbL > 0) display.print("+");
  display.print(roundedDbL);
  display.setCursor(label_x, 3);
  display.print("L");
  display.setCursor(6, 20);
  display.print("dB");
  drawVUMeterBar(bar_x_start, 39, dbR, peakR);
  display.setCursor(1, 47);
  int roundedDbR = round(dbR); 
  if (roundedDbR > 0) display.print("+");
  display.print(roundedDbR); 
  display.setCursor(label_x, 37);
  display.print("R");
  display.setCursor(6, 55);
  display.print("dB");
  display.setCursor(52, 28);
  display.print("PATRO DJ");
  display.display();
}