/*
A great Servero demo and live display data
Designed by SunFounder Maker Education
*/

#include <Servo.h>           // Include servo motor control library
#include <Wire.h>            // Include I2C communication library
#include <Adafruit_GFX.h>    // Include core graphics library
#include <Adafruit_SSD1306.h>// Include SSD1306 OLED display library

// OLED display parameters
#define SCREEN_WIDTH 128     // OLED display width in pixels
#define SCREEN_HEIGHT 64     // OLED display height in pixels
#define OLED_RESET    -1     // No hardware reset pin used
#define SCREEN_ADDR   0x3C   // I2C address for OLED display
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);

// Rotary encoder pins
#define ENCODER_CLK  11      // Encoder output A (CLK)
#define ENCODER_DT   10      // Encoder output B (DT)
#define ENCODER_SW    9      // Encoder button switch (SW)

// Servo control pin
#define SERVO_PIN     3      // Servo signal pin

Servo myServo;              // Create servo object
int angle = 90;             // Initial servo angle (0-180)
int stepSize = 1;           // Rotation step: 1°, 5°, or 10°
int lastClkState;           // Previous state of CLK for edge detection
int lastSwState;            // Previous state of SW for debounce
unsigned long lastDebounce = 0;
const unsigned long DEBOUNCE_MS = 50; // Debounce time in milliseconds

void setup() {
  // Initialize encoder pins with internal pull-ups
  pinMode(ENCODER_CLK, INPUT_PULLUP);
  pinMode(ENCODER_DT,  INPUT_PULLUP);
  pinMode(ENCODER_SW,  INPUT_PULLUP);

  Serial.begin(9600);      // Start serial communication for debugging

  myServo.attach(SERVO_PIN); // Attach servo to control pin
  myServo.write(angle);    // Move servo to starting angle

  // Initialize OLED display and halt if failed
  if (!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDR)) {
    Serial.println("SSD1306 allocation failed");
    while (true);          // Stop execution on failure
  }
  display.clearDisplay();  // Clear the buffer
  display.display();       // Display cleared buffer

  // Read initial encoder states
  lastClkState = digitalRead(ENCODER_CLK);
  lastSwState  = digitalRead(ENCODER_SW);

  updateDisplay();         // Draw the initial UI
}

void loop() {
  // Detect rotation on rising edge of CLK
  int clkState = digitalRead(ENCODER_CLK);
  if (clkState != lastClkState && clkState == HIGH) {
    // Determine direction using DT
    if (digitalRead(ENCODER_DT) != clkState) angle = max(0, angle - stepSize);
    else                                   angle = min(180, angle + stepSize);
    myServo.write(angle);  // Move servo to new angle
    updateDisplay();       // Update the display
  }
  lastClkState = clkState;

  // Detect button press with debounce
  int swState = digitalRead(ENCODER_SW);
  if (swState != lastSwState) {
    unsigned long now = millis();
    if (now - lastDebounce > DEBOUNCE_MS && swState == LOW) {
      // Cycle step sizes: 1 -> 5 -> 10
      if      (stepSize == 1)  stepSize = 5;
      else if (stepSize == 5)  stepSize = 10;
      else                      stepSize = 1;
      updateDisplay();        // Refresh display after change
    }
    lastDebounce = now;
  }
  lastSwState = swState;
}

// Draw UI elements on OLED display
void updateDisplay() {
  // Energy bar region (0-20px)
  display.fillRect(0, 0, SCREEN_WIDTH, 20, BLACK);
  display.drawRect(0, 0, SCREEN_WIDTH, 20, WHITE);
  int barWidth = map(angle, 0, 180, 0, SCREEN_WIDTH);
  if (barWidth > 2) display.fillRect(1, 1, barWidth - 2, 18, WHITE);

  // Tick marks and labels (20-32px)
  display.fillRect(0, 20, SCREEN_WIDTH, 12, BLACK);
  display.setTextSize(1);
  display.setTextColor(WHITE);
  int ticks[] = {0, 30, 60, 90, 120, 150, 180};
  for (int deg : ticks) {
    int x = map(deg, 0, 180, 0, SCREEN_WIDTH);
    display.drawLine(x, 20, x, 24, WHITE);
    char buf[4]; snprintf(buf, sizeof(buf), "%d", deg);
    int16_t tbx, tby; uint16_t tbw, tbh;
    display.getTextBounds(buf, 0, 0, &tbx, &tby, &tbw, &tbh);
    display.setCursor(x - tbw/2, 25);
    display.print(buf);
  }

  // Info region (32-64px)
  display.fillRect(0, 32, SCREEN_WIDTH, 32, BLACK);
  int baseY = 34;

  // Draw "Angle" label
  display.setTextSize(1);
  const char* lblA = "Angle";
  int16_t ax, ay; uint16_t aw, ah;
  display.getTextBounds(lblA, 0, 0, &ax, &ay, &aw, &ah);
  display.setCursor(32 - aw/2, baseY);
  display.print(lblA);

  // Draw numeric angle value
  char valA[4]; snprintf(valA, sizeof(valA), "%d", angle);
  display.setTextSize(2);
  int16_t vx, vy; uint16_t vw, vh;
  display.getTextBounds(valA, 0, 0, &vx, &vy, &vw, &vh);
  int valX = 32 - vw/2;
  int valY = baseY + ah + 4;
  display.setCursor(valX, valY);
  display.print(valA);
  // Hollow degree symbol next to angle
  int r = max(1, vh / 6);
  display.drawCircle(valX + vw + r + 1,
                    valY + vh/2 - r,
                    r, WHITE);

  // Draw "Step" label
  display.setTextSize(1);
  const char* lblS = "Step";
  int16_t sx, sy; uint16_t sw_, sh;
  display.getTextBounds(lblS, 0, 0, &sx, &sy, &sw_, &sh);
  display.setCursor(96 - sw_/2, baseY);
  display.print(lblS);

  // Draw numeric step value
  char valS[4]; snprintf(valS, sizeof(valS), "%d", stepSize);
  display.setTextSize(2);
  display.getTextBounds(valS, 0, 0, &sx, &sy, &sw_, &sh);
  int sX = 96 - sw_/2;
  display.setCursor(sX, valY);
  display.print(valS);
  // Hollow degree symbol next to step
  int r2 = max(1, sh / 6);
  display.drawCircle(sX + sw_ + r2 + 1,
                    valY + sh/2 - r2,
                    r2, WHITE);

display.display();
}