#include "User_Setup.h"
#include <SPI.h>
#include <TFT_eSPI.h>
#include "NotoSansBold15.h"
#include "NotoSansBold36.h"
#include "CourierB24.h"
#include "Unicode_Test_72.h"
#include "background.h"

#define SOLENOID_PIN 4 // Define your actual solenoid pin
#define RST 6
#define T5 14
#define T10 12
#define T15 10
#define PLUS1 8

TFT_eSPI tft = TFT_eSPI();
TFT_eSprite spr = TFT_eSprite(&tft);
TFT_eSprite sprT = TFT_eSprite(&tft);

int oldV = -1;
int v;
float vf1;
unsigned long tNow;
unsigned long tRead;
unsigned int timeout = 0; // Starts at 0
byte minutes, seconds;
unsigned long debounce;

void setup() {
  Serial.begin(115200);
  
  pinMode(SOLENOID_PIN, OUTPUT);
  digitalWrite(SOLENOID_PIN, LOW);

  pinMode(RST, INPUT_PULLUP);
  pinMode(T5, INPUT_PULLUP);
  pinMode(T10, INPUT_PULLUP);
  pinMode(T15, INPUT_PULLUP);
  pinMode(PLUS1, INPUT_PULLUP);

  tft.begin();
  tft.setRotation(3);
  tft.setSwapBytes(true);
  tft.pushImage(0, 0, 320, 240, (uint16_t *)image1);
  
  spr.loadFont(NotoSansBold36);
  spr.setTextColor(TFT_WHITE, TFT_BLACK);
  spr.createSprite(200, 36);

  sprT.loadFont(CourierB24);
  sprT.setTextColor(TFT_YELLOW, TFT_BLACK);
  sprT.createSprite(180, 24); // Increased width for "MIN:SEC" string

  tNow = millis();
  tRead = millis();
}

void loop() {
  // --- Button Handling ---
  if(millis()-debounce > 250){
    if (digitalRead(T5) == LOW) { timeout = 300; debounce = millis(); }
    if (digitalRead(T10) == LOW) { timeout = 600; debounce = millis(); }
    if (digitalRead(T15) == LOW) { timeout = 900; debounce = millis(); }
    if (digitalRead(PLUS1) == LOW) { timeout += 60; debounce = millis(); }
    if (digitalRead(RST) == LOW) { timeout = 0; debounce = millis(); }
  }
  // --- Solenoid Control ---
  if (timeout > 0) {
    digitalWrite(SOLENOID_PIN, HIGH);
  } else {
    digitalWrite(SOLENOID_PIN, LOW);
  }

  // --- Timer Update (Every 1 Second) ---
  if (millis() - tNow >= 1000) {
    tNow = millis();
    if (timeout > 0) timeout--;

    sprT.fillSprite(TFT_BLACK);
    sprT.setCursor(0, 0);
    minutes = timeout / 60;
    seconds = timeout % 60;
    
    if (minutes < 10) sprT.print("0");
    sprT.print(minutes);
    sprT.print(":");
    if (seconds < 10) sprT.print("0");
    sprT.print(seconds);
    sprT.pushSprite(200, 45);
  }

  // --- CO2 Sensor Update (Every 500ms) ---
 
  if (millis() - tRead >= 500) {
    tRead = millis();
     v = analogRead(3);
    if (abs(oldV - v) > 5) { // Small threshold to prevent jitter
      vf1 = v / 81.92; // Adjust scaling for your specific CO2 sensor
      oldV = v;

      spr.fillSprite(TFT_BLACK);
      spr.setCursor(0, 0);
      spr.print(vf1, 1);
      spr.print("%");
      spr.pushSprite(100, 80);
    }
  }
}