//   funguje i2c scan
//   !!! nekde na i2c to vidi nejake 0x27 i kdyz neni, proto testuju isr vektor na 0x26
//   funguje PCF read vcetne ISR
//   funguje PCA pwm serva - na zkousku jen 2 pwm vystupy
//   funguje WS2812
//   L298 simulace motoru funguje
//   zkouska PWM LED vz pwm3 kod od luisllamas - simulace zamrzne a nejede
//  Arduino kompilace ESP32 Dev Module:
//  Projekt zabírá 1029544 bytů (78%)  úložného místa pro program. Maximum je 1310720 bytů.
//  Globální proměnné zabírají 49668 bytů (15%)  dynamické paměti, 278012 bytů zůstává pro lokální proměnné. Maximum je 327680 bytů.
//  za ten objem asi muze wifi

#include <WiFi.h>
#include <Wire.h>
#include <I2cDiscreteIoExpander.h>    // PCF85xx library
#include <Adafruit_PWMServoDriver.h>  // PWMservo library
#include <FastLED.h>
#define NUM_LEDS 16
#define DATA_PIN 15
CRGB leds[NUM_LEDS];

#define NTP_SERVER     "pool.ntp.org"
#define UTC_OFFSET     0
#define UTC_OFFSET_DST 0

#include <LiquidCrystal_I2C.h> // Importa a biblioteca para o LCD I2C.
LiquidCrystal_I2C lcd(0x27, 16, 2); // Define o endereço I2C do LCD e seu tamanho.

#define Add0 32     // PCF chip1 INToutput read

#define LEDPIN 25
#define DEBOUNCE_DELAY 100      // puvodni 200  - debouncing isr

/*
bool interrupt = false;    // true on interrupt
bool ledState = false;
uint32_t lastInterruptTime = 0;
*/

volatile bool interrupt = false;    // true on interrupt
volatile bool ledState = false;
volatile uint32_t lastInterruptTime = 0;
volatile uint16_t ISRVector;
uint16_t ISR_Xvector;

uint8_t ISRdev = 6;         // ISR vector device

/*volatile */ uint8_t error, address, reg, data;

uint8_t dev_addr = 0x40; //0x40 - 12C Address
uint8_t mode1 = 0;     //0x00 location for Mode1 register address
uint8_t mode2 = 1;     //0x01 location for Mode2 register address
uint16_t PRE_SCALE =30; 
uint8_t led0 = 6;      //0x06 location for start  LED0 registers
uint8_t rst = 1;       //0x01 reset device
uint8_t rval = 0;      //read register value

uint16_t led_on;
uint16_t led_off;
uint8_t ledN;

uint8_t led_stat[16];

/**********************************************************************/
#define PCA9685_ADDRESS_1  0x40         // I2C PCA9685
#define PCA9685_ADDRESS_2  0x41         // I2C PCA9685
#define PCA9685_ADDRESS_3  0x42         // I2C PCA9685
#define PCA9685_ADDRESS_4  0x43         // I2C PCA9685

// Adafruit_PWMServoDriver pwm1 = Adafruit_PWMServoDriver(PCA9685_ADDRESS_1);
Adafruit_PWMServoDriver pwm2 = Adafruit_PWMServoDriver(PCA9685_ADDRESS_2);
Adafruit_PWMServoDriver pwm3 = Adafruit_PWMServoDriver(PCA9685_ADDRESS_3);
// Adafruit_PWMServoDriver pwm4 = Adafruit_PWMServoDriver(PCA9685_ADDRESS_4);

#define SERVOMIN 150    // This is the 'minimum' pulse length count (out of 4096)
#define SERVOMAX 600   // This is the 'maximum' pulse length count (out of 4096)
#define SERVO_FREQ 50  // Analog servos run at ~50 Hz updates

// Adjust these angles according to Servo360_PCA_AngleFInd code that I have provided
int leftAngle = 0;     // angel for motor to move left (If the motor move in right you can change the name to rightAngle)
int rightAngle = 180;  // angel for motor to move right (If the motor move in left you can change the name to leftAngle)
int stopAngle = 90;    // Angle when motor stops

// our servo # counter
uint8_t servonum = 0;
byte totalServos = 2;  // Define how many servos we are using here

// Define the time (in milliseconds 1 second = 1000 millisecond) for each servo to move in right direction
int rightMoveTime[13] = { 200, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100 };  // Wait for this millisecond when motor move right
int stopWaitTime[13] =  { 200, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100 };   // Wait for this millisecond after motor has reached it's point
int leftMoveTime[13] =  { 200, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100 };   // Wait for this millisecond when motor move left
/*************************************************************************/

// create I2cDiscreteIoExpander objects
I2cDiscreteIoExpander device[8] = {0,1,2,3,4,5,6,7};  //  [8=total number]


uint8_t PCF_addr[8] = {0x20,0x21,0x22,0x23,0x24,0x25,0x26,0x27};
uint8_t PCA_addr[8] = {0x40,0x41,0x42,0x43,0x44,0x45,0x46,0x47};

/********************************** ISR *********************************/

void IRAM_ATTR doISR(){
//void ARDUINO_ISR_ATTR doISR() {
  uint32_t currentTime = millis();
  if (currentTime - lastInterruptTime > DEBOUNCE_DELAY) {     // <<<---- tady je to kouzlo
    interrupt = true;
    lastInterruptTime = currentTime;
    ISR_Xvector = device[ISRdev].getPorts();
/*
    if (interrupt) {
      Serial.println("ON");     // to jeste zvlada bez havarie
    } else {
      Serial.println("OFF");     // to jeste zvlada bez havarie
    }
*/
//    ledState = !ledState;   // jen střídavě přepíná
//  digitalWrite(LEDPIN, ledState);     // POZOR - dlouhá loop - dlouhá odezva - ošetřit jinak
//  digitalWrite(LEDPIN, interrupt);     // POZOR - dlouhá loop - dlouhá odezva - ošetřit jinak
  }
/*  //Serial to jednoznačně kousne
  for(uint8_t idx = 6; idx<7; idx++){
    Serial.print("whe isr - inputs on device : ");
    Serial.print(idx, HEX);
    Serial.print(" bin : ");
    Serial.println(getChangedInputValue(idx), BIN);
  }
*/
// ISR_Xvector = device[ISRdev].getPorts();    // tady to simulace stihala
}

void setup() {

  pinMode(Add0, INPUT_PULLUP);
  pinMode(34, INPUT_PULLUP);
  pinMode(LEDPIN, OUTPUT);

  Serial.begin(115200);
  Serial2.begin(9600, SERIAL_8N1, 16, 17);  // Nextion serial
//  Serial2.begin(9600);  // Nextion serial2
  Serial.println("\nI2C Scanner");
  Serial2.println("Serial 2 NEX");

  Wire.begin();
  
  lcd.init();
  lcd.backlight();
  lcd.clear();
  lcd.setCursor(0, 0);
  lcd.print("    I2C scan    ");
  lcd.setCursor(0, 1);
  lcd.print("  > scanning >  ");

  int nDevices;
  Serial.println("Scanning...");
  nDevices = 0;
  for(address = 1; address < 127; address++ ) {
    Wire.beginTransmission(address);
    error = Wire.endTransmission();
    if (error == 0) {
      Serial.print("I2C device found at address 0x");
      if (address<16) {
        Serial.print("0");
      }
      Serial.println(address,HEX);
      nDevices++;
    }
    else if (error==4) {
      Serial.print("Unknow error at address 0x");
      if (address<16) {
        Serial.print("0");
      }
      Serial.println(address,HEX);
    }    
  }
  if (nDevices == 0) {
    Serial.println("No I2C devices found\n");
  }
  else {
    Serial.println("done\n");

//  LCD_displ("    I2C scan    ", "  > finished >  ");
    //  lcd.setCursor(0, 0);
    //  lcd.print("    I2C scan    ");
      lcd.setCursor(0, 1);
      lcd.print("    finished    ");

  }
  lcd.clear();
  lcd.backlight();
  lcd.setCursor(0, 0);
  lcd.print("Connecting to ");
  lcd.setCursor(0, 1);
  lcd.print("WiFi ");

  WiFi.begin("Wokwi-GUEST", "", 6);
  while (WiFi.status() != WL_CONNECTED) {
    delay(250);
    spinner();
  }

  Serial.println("");
  Serial.println("WiFi connected");
  Serial.print("IP address: ");
  Serial.println(WiFi.localIP());

  lcd.clear();
  lcd.setCursor(0, 0);
  lcd.println("Online");
  lcd.setCursor(0, 1);
  lcd.println("Updating time...");

  configTime(UTC_OFFSET, UTC_OFFSET_DST, NTP_SERVER);
  setTimezone("CET-1CEST,M3.5.0,M10.5.0/3");
//  initTime("CET-1CEST,M3.5.0,M10.5.0/3"); // TZ-String for Europe/Berlin


/************************************************************************/
//  prime ovladani PCA 0x40 pro LED

//set for auto-increnent
///reg = mode1;
data = 160;           // 0b10100000  viz Mode register 1 PCA9685 str.13   RESTART a AUTOINCREMENT
//data = 176;           // 0b11100000  viz Mode register 1 PCA9685 str.13   RESTART, SLEEP a AUTOINCREMENT
//data = 32;           // 0b00100000  viz bit 5 Mode register 1 PCA9685 str.13


data = 160;           // 0b10100000  viz Mode register 1 PCA9685 str.13   RESTART a AUTOINCREMENT
//data = 176;           // 0b11100000  viz Mode register 1 PCA9685 str.13   RESTART, SLEEP a AUTOINCREMENT
//data = 32;           // 0b00100000  viz bit 5 Mode register 1 PCA9685 str.13

WRITE_REG(0x40, mode1, data);             //mode1 register
delay(50);
// Choose below the desired output mode
//Direct LED connection
// -- set to outpud mode INVRT= 1  OUTDRV =0
///reg = mode2;
data = 16;
WRITE_REG(0x40, mode2, data);             //mode2 register
delay(50);

// The PRE_SCALE register can only be set when the SLEEP bit of MODE1 register is set to logic 1.
// mode1 | 0b00001000
WRITE_REG(0x40, mode1, 176);    //mode1 SLEEP bit
delay(50);
uint16_t prescale = 121;       // => 50 Hz
WRITE_REG(0xFE, PRE_SCALE, prescale);     //prescale factor
delay(50);
// mode1 & 0b11110111
WRITE_REG(0x40, mode1, data);             //mode1 register
delay(50);

/************************************************************************/

  // PCF init preset
  // bez nasled disable to nehraje
  for(uint8_t i = 0; i<8; i++){
  device[i].disableBitwiseInversion();
  }

/***===================================================================***/
//  pwm1.begin();  // Initialize PWM instance
//  pwm1.setOscillatorFrequency(27000000);
//  pwm1.setPWMFreq(SERVO_FREQ);  // Analog servos run at ~50 Hz updates

  pwm2.begin();  // Initialize PWM instance
  pwm2.setOscillatorFrequency(27000000);
  pwm2.setPWMFreq(SERVO_FREQ);  // Analog servos run at ~50 Hz updates

//  pwm3.begin();  // Initialize PWM instance
//  pwm3.setOscillatorFrequency(27000000);
//  pwm3.setPWMFreq(SERVO_FREQ);  // Analog servos run at ~50 Hz updates

//  zkouska ale simulace pak zamrzne viz v loop luisllamas kod
  pwm3.begin();
  // Set the frequency to the maximum (1600Hz)
  pwm3.setPWMFreq(1600); 

//  pwm4.begin();  // Initialize PWM instance
//  pwm4.setOscillatorFrequency(27000000);
//  pwm4.setPWMFreq(SERVO_FREQ);  // Analog servos run at ~50 Hz updates

  // Stop all servos
  for (int servoNum = 0; servoNum < totalServos; servoNum++) {  // initially stop all servo motors
    pwm2.setPWM(servoNum, 0, getAnglePulse(stopAngle));
  }
/***===================================================================***/
/******************** Nextion init *************/
  // Serial2.begin(9600, SERIAL_8N1, 16, 17);  // Nextion serial
  // sendNumberData("n0", 255);

  FastLED.addLeds<WS2812, DATA_PIN, GRB>(leds, NUM_LEDS);  // GRB ordering is typical 

  attachInterrupt(Add0, doISR, FALLING);      // INT signal je aktivni stavem L, vynuluje se prectenim nebo zapisem do portu
                                              // vynuluje se i vracenim vstupu do puv.stavu
  printLocalTime();
  delay(500);
  //ALL_LED
ledN = 61;  //odkaz na registr 250  ALL_LED
led_on = 4096;      // zhasne vsechny LED - stav H - LED jsou proti +Vcc
led_off = 4095;     // k tomu musi byt  led_on = 4095 jinak nestiha simulace
WRITE_LED(0x40, ledN, led_on, led_off);

}

/**************************************************************/
/**********  MAIN LOOP - MAIN LOOP - MAIN LOOP  ***************/
/**************************************************************/
void loop() {
/*
      lcd.clear();
      lcd.setCursor(0, 0);
      lcd.print("Main loop       ");
      lcd.setCursor(0, 1);
      lcd.print(" > in progress >");
*/
/*
    digitalWrite(LEDPIN, ledState);     // POZOR - dlouhá loop - dlouhá odezva - ošetřit jinak
    Serial.print("var ledState : ");
    Serial.println(ledState);
    digitalWrite(LEDPIN, ledState);     // POZOR - dlouhá loop - dlouhá odezva - ošetřit jinak
*/

/* zpracovat flag if(interrupt=true) a pak ho vynulovat  */
    digitalWrite(LEDPIN, interrupt);     // POZOR - dlouhá loop - dlouhá odezva - ošetřit jinak

    Serial.print("var interrupt : ");
    Serial.println(interrupt);

/*
    device[ISRdev].digitalRead();
    ISRVector = device[ISRdev].getPorts();  // az precteni PCF s aktivnim INT schodi vystup int PCF

    Serial.print("ISRVector getPorts : ");
    Serial.println(ISRVector, HEX);
//    ISR_Xvector = XreadInputs(ISRdev);    // az precteni PCF s aktivnim INT schodi vystup int PCF // tohle je asi pomalejsi - cca 2 millis

*/
    Serial.print("ISR_Xvector from isr : ");
    Serial.println(ISR_Xvector, HEX);                     // ISR?Xvector je nacteni z isr
//  zparcovat ISR vector a pak ho vynulovat / POZOR - asi mutexem osetrit podhozeni 
//  {..........................................}
    ISR_Xvector = 0xFFFF;
    interrupt = false;

    vTaskDelay(1100 / portTICK_PERIOD_MS);

// delay(200);


// nasledujici zpracovani =  precteni portu PCF schodi vystupy INT do LOW ( HIGH je aktivni)
  for(uint8_t idx = 0; idx<7; idx++){
    Serial.print("inputs on device : ");
    Serial.print(idx, HEX);
    Serial.print(" bin : ");
    Serial.println(getChangedInputValue(idx), BIN);
  }
//  detachInterrupt(Add0);
      Serial.println("===== mirror 1 =====");
      //delay(20);
      mirrorInputOntoOutputs(0);  // pozn: zrcadli se LowByte do HighByte, ISR funguje
      delay(20);

//      Serial.println("===== mirror 2 =====");
      //delay(20);
///      mirrorInputOntoOutputs(1);
//      Serial.println("===== mirror 3 =====");
      //delay(20);
///      mirrorInputOntoOutputs(2);
//      Serial.println("===== mirror 4 =====");
      //delay(20);
///      mirrorInputOntoOutputs(3);
//      Serial.println("===== mirror 5 =====");
      //delay(20);
///      mirrorInputOntoOutputs(4);
//      Serial.println("===== mirror 6 =====");
      //delay(20);
///      mirrorInputOntoOutputs(5);
/*
      Serial.println("ISR vectors on device(7)");
      //delay(20);
      readInputs(7);
///      mirrorInputOntoOutputs(7);
*/

/************************** PCA LED *********************************************/
/**/
//Serial.println("loop 0");
ledN = 0;
led_on = 4096;
led_off = 4095;
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 1");
ledN = 1;
led_on = 4095;  //  prioritu ma LED_full_OFF    - !!!!!!!!!
led_off = 4096; // k tomu musi byt  led_on = 4095 nebo 4096(LED_ON) jinak nestiha simulace
// tyhle parametry nefungujou - ale nevim proc
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 2");
ledN = 2;
led_on = 4096;  //  jas LED cim vyssi hodnota tim vic sviti / LED proti Vcc
led_off = 4095;
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 3");
ledN = 3;
led_on = 4095;
led_off = 4096;
WRITE_LED(0x40, ledN, led_on, led_off);
/*/
/*  //ALL_LED
ledN = 61;  //odkaz na registr 250  ALL_LED
led_on = 4095;
led_off = 4095;
WRITE_LED(0x40, ledN, led_on, led_off);
*/

///WRITE_LED(0x40, 0, 4096, 4095);

/****************************************************************************/

leds[0]    = CRGB::Orange;
leds[1]    = CRGB::Green;
leds[2]    = CRGB::Red;
leds[3]    = CRGB::Black;
//...
leds[6]    = CRGB::Blue;
leds[7]    = CRGB::White;

FastLED.show();

      pwm3.setPWM(0, 0, 4096);
      pwm3.setPWM(1, 4096,0);
      pwm3.setPWM(2, 0, 4096);
      pwm3.setPWM(3, 4096,0);

delay(500);


/***====================================================================***/
    // Run one servo at a time
// test pwm nr 1 only:
/*
    for (int currentServo = 0; currentServo < totalServos; currentServo++) {
      pwm1.setPWM(currentServo, 0, getAnglePulse(rightAngle));  // First move servo to right side
      delay(rightMoveTime[currentServo]);                                    // move motor in right for this time defined in start
      pwm1.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop servo at this point
      delay(stopWaitTime[currentServo]);                                    // Keep motor stopped at this position defined in start
      pwm1.setPWM(currentServo, 0, getAnglePulse(leftAngle));   // Now move servo to left side back
      delay(leftMoveTime[currentServo]);                                     // move motor in left for this time defined in start
      pwm1.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop This servo
      delay(50);                                              // wait for 50 milliseconds before moving next servo
      }
*/
// test pwm nr 2 only:
    for (int currentServo = 0; currentServo < totalServos; currentServo++) {
      pwm2.setPWM(currentServo, 0, getAnglePulse(rightAngle));  // First move servo to right side
      delay(rightMoveTime[currentServo]);                                    // move motor in right for this time defined in start
      pwm2.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop servo at this point
      delay(stopWaitTime[currentServo]);                                    // Keep motor stopped at this position defined in start
      pwm2.setPWM(currentServo, 0, getAnglePulse(leftAngle));   // Now move servo to left side back
      delay(leftMoveTime[currentServo]);                                     // move motor in left for this time defined in start
      pwm2.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop This servo
      delay(50);                                              // wait for 50 milliseconds before moving next servo
    }
/*
// test pwm nr 3 only:
    for (int currentServo = 0; currentServo < totalServos; currentServo++) {
      pwm3.setPWM(currentServo, 0, getAnglePulse(rightAngle));  // First move servo to right side
      delay(rightMoveTime[currentServo]);                                    // move motor in right for this time defined in start
      pwm3.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop servo at this point
      delay(stopWaitTime[currentServo]);                                    // Keep motor stopped at this position defined in start
      pwm3.setPWM(currentServo, 0, getAnglePulse(leftAngle));   // Now move servo to left side back
      delay(leftMoveTime[currentServo]);                                     // move motor in left for this time defined in start
      pwm3.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop This servo
      delay(50);                                              // wait for 50 milliseconds before moving next servo
  }
*/
/*
  // https://www.luisllamas.es/en/control-16-servos-16-pwm-outputs-arduino-pca9685/
  for (uint16_t duty = 0; duty < 4096; duty += 8)
  {
    for (uint8_t pwmNum = 0; pwmNum < 16; pwmNum++)
    {
      // Adjust PWM with ON at tick=0 and OFF at tick=duty
      pwm3.setPWM(pwmNum, 0, duty);      // to simulace nezvlada ani s knihownou PWM a zamrzne...
    }
  }
*/
/*
// test pwm nr 4 only:
    for (int currentServo = 0; currentServo < totalServos; currentServo++) {
      pwm4.setPWM(currentServo, 0, getAnglePulse(rightAngle));  // First move servo to right side
      delay(rightMoveTime[currentServo]);                                    // move motor in right for this time defined in start
      pwm4.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop servo at this point
      delay(stopWaitTime[currentServo]);                                    // Keep motor stopped at this position defined in start
      pwm4.setPWM(currentServo, 0, getAnglePulse(leftAngle));   // Now move servo to left side back
      delay(leftMoveTime[currentServo]);                                     // move motor in left for this time defined in start
      pwm4.setPWM(currentServo, 0, getAnglePulse(stopAngle));   // Stop This servo
      delay(50);                                              // wait for 50 milliseconds before moving next servo
    }
*/
//
/***====================================================================***/
/**/
//Serial.println("loop 0e");
ledN = 0;
led_on = 4095;
led_off = 4096;
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 1e");
ledN = 1;
led_on = 2048;      // jine nez 4096 nebo 4095 ignoruje
led_off = 4095;
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 2e");
ledN = 2;
led_on = 4095;
led_off = 4096;
WRITE_LED(0x40, ledN, led_on, led_off);

//Serial.println("loop 3e");
ledN = 3;
led_on = 4096;
led_off = 4095;
WRITE_LED(0x40, ledN, led_on, led_off);
/*/
/*  //ALL_LED
ledN = 61;  //odkaz na registr 250  ALL_LED
led_on = 4095;
led_off = 4096;     // k tomu musi byt  led_on = 4095 jinak nestiha simulace
WRITE_LED(0x40, ledN);
*/

/**************************************************************************/

leds[0]    = CRGB::Orange;
leds[1]    = CRGB::Black;
leds[2]    = CRGB::Black;
leds[3]    = CRGB::Orange;
//...
leds[6]    = CRGB::White;
leds[7]    = CRGB::Blue;

FastLED.show();

      pwm3.setPWM(0, 4096, 0);
      pwm3.setPWM(1, 0, 4096);
      pwm3.setPWM(2, 4096, 0);
      pwm3.setPWM(3, 0, 4096);


//delay(200);
delay(1000);
}
/***************  END OF MAIN LOOP - END OF MAIN LOOP  ***************/

void LED_SW(uint8_t PCA_addr, uint16_t ledN, uint16_t led_on, uint16_t led_off){
if (led_stat[ledN] == 0) {
   led_stat[ledN] = 1;
   led_on = 4096;
   led_off = 0;
   WRITE_LED(PCA_addr, ledN, led_on, led_off);
  }
else{
   led_stat[ledN] = 0;
   led_on = 0;
   led_off = 4096;
   WRITE_LED(PCA_addr, ledN, led_on, led_off);
  }
}

void SetOFF() {
led_on = 0;
led_off = 4096;
WRITE_LED;
}

void READREG(uint8_t dev_addr) {
Wire.beginTransmission( dev_addr );
Wire.write(reg);
error = Wire.endTransmission();

Wire.beginTransmission( dev_addr );
Wire.requestFrom(dev_addr,1);     //start a transaction to read 1 byte
rval = Wire.read();               //read the byte
error = Wire.endTransmission();
}

void WRITE_LED(uint8_t dev_addr, uint8_t ledN, uint16_t led_on, uint16_t led_off){
byte ah,al;
Wire.beginTransmission( dev_addr );
Wire.write(led0 + 4*ledN);
ah = led_on >> 8;
al = led_on && 255;
Wire.write(al);
Wire.write(ah);
ah = led_off >> 8;
al = led_off and 255;
Wire.write(al);
Wire.write(ah);
error = Wire.endTransmission();
//Serial.print("error > ");
/*
Serial.print(error);
Serial.print(" on addr 0x");
Serial.print(dev_addr,HEX);
Serial.print(" LED:");
Serial.print(ledN);
Serial.print(" led_on :");
Serial.print(led_on);
Serial.print(" led_off :");
Serial.println(led_off);
*/
}

void WRITE_REG(uint8_t dev_addr, uint8_t reg, uint8_t data ){
Wire.beginTransmission( dev_addr );
Wire.write(reg);
Wire.write(data);
error = Wire.endTransmission();
}
/**************************************************************************/

int getAnglePulse(int inpAngle) {
  int retPulse = map(inpAngle, leftAngle, rightAngle, SERVOMIN, SERVOMAX);
  return retPulse;
}

uint16_t getChangedInputValue(uint8_t idx) {
//    Serial.println("Get Input");
    device[idx].digitalRead();
    return device[idx].getPorts();
}

void mirrorInputOntoOutputs(uint8_t idx) {

    uint16_t bothports = getChangedInputValue(idx);
    uint16_t inputs = lowByte(bothports);
    // Mirror the inputs to the outputs
    // leave the inputs, as inputs (i.e. writing high)
    uint16_t newValue = word(inputs, 0xff) ; // (inputs << 8) | 0xff;
/*    Serial.print("Inputs read as 0x");
    Serial.print(inputs, HEX);
*/    //Serial.println(" being mirrored to out");
    device[idx].digitalWrite(newValue);
/*    Serial.print("Wrote 2 bytes: port0 -> 0x");
    Serial.print(lowByte(newValue), HEX);
    Serial.print(" port1 -> 0x");
    Serial.print(highByte(newValue), HEX);
    Serial.print(" to device ");
    Serial.println((int)idx);
*/  }

void readInputs(uint8_t idx) {      // pouze posle na ser.port
    uint16_t newValue = getChangedInputValue(idx);
    Serial.print("Inputs read 0x");
    Serial.print(newValue, HEX);
    Serial.print(" on device ");
    Serial.println((int)idx);
//     if(newValue < 0xFFFE)
//      device[idx].digitalWrite (0xFFFE);
//      else device[idx].digitalWrite (0xFFFF);
  }

uint16_t XreadInputs(uint8_t idx) {   //  funkce, vraci stav vstupu
    uint16_t newValue = getChangedInputValue(idx);
    Serial.print("Inputs Xread 0x");
    Serial.print(newValue, HEX);
    Serial.print(" on device ");
    Serial.println((int)idx);
//     if(newValue < 0xFFFE)
//      device[idx].digitalWrite (0xFFFE);
//      else device[idx].digitalWrite (0xFFFF);
//   delay(50);
    return newValue;  
  }

/*********************  NEX  *****  NEX  *******  NEX  ******************/
void sendTermination() {
  Serial2.write(0xFF);
  Serial2.write(0xFF);
  Serial2.write(0xFF);
}
void sendWaveformData(int waveformId, int channel, int value) {
//  Serial.println(value);
  Serial2.print("add ");
  Serial2.print(waveformId);
  Serial2.print(",");
  Serial2.print(channel);
  Serial2.print(",");
  Serial2.print(value);
  sendTermination();
}
void sendTextData(const char* componentName, int value) {
  Serial2.print(componentName);
  Serial2.print(".txt=\"");
  Serial2.print(value);
  Serial2.print("\"");
  sendTermination();
}
void sendNumberData(const char* componentName, int value) {
  Serial2.print(componentName);
  Serial2.print(".val=");
  Serial2.print(value);
  sendTermination();
}
void sendGaugeData(const char* componentName, int value) {
  Serial2.print(componentName);
  Serial2.print(".val=");
  Serial2.print(value);
  sendTermination();
}
void sendProgressBarData(const char* componentName, int value) {
  Serial2.print(componentName);
  Serial2.print(".val=");
  Serial2.print(value);
  sendTermination();
}

void spinner() {
  static int8_t counter = 0;
  const char* glyphs = "\xa1\xa5\xdb";
  lcd.setCursor(15, 1);
  lcd.print(glyphs[counter++]);
  if (counter == strlen(glyphs)) {
    counter = 0;
  }
}
/************************** NTP *********************************/
/*
void printLocalTime(){      // puvodni od https://randomnerdtutorials.com/esp32-date-time-ntp-client-server-arduino/
  struct tm timeinfo;
  if(!getLocalTime(&timeinfo)){
    Serial.println("Failed to obtain time");
    return;
  }
  Serial.println(&timeinfo, "%A, %B %d %Y %H:%M:%S");
  Serial.print("Day of week: ");
  Serial.println(&timeinfo, "%A");
  Serial.print("Month: ");
  Serial.println(&timeinfo, "%B");
  Serial.print("Day of Month: ");
  Serial.println(&timeinfo, "%d");
  Serial.print("Year: ");
  Serial.println(&timeinfo, "%Y");
  Serial.print("Hour: ");
  Serial.println(&timeinfo, "%H");
  Serial.print("Hour (12 hour format): ");
  Serial.println(&timeinfo, "%I");
  Serial.print("Minute: ");
  Serial.println(&timeinfo, "%M");
  Serial.print("Second: ");
  Serial.println(&timeinfo, "%S");

  Serial.println("Time variables");
  char timeHour[3];
  strftime(timeHour,3, "%H", &timeinfo);
  Serial.println(timeHour);
  char timeWeekDay[10];
  strftime(timeWeekDay,10, "%A", &timeinfo);
  Serial.println(timeWeekDay);
  Serial.println();
}
*/
void printLocalTime() {
  struct tm timeinfo;
  if (!getLocalTime(&timeinfo)) {
    lcd.setCursor(0, 1);
    lcd.println("Connection Err  ");
    Serial.println("Connection Err");
    return;
  }

  lcd.setCursor(8, 0);
  lcd.println(&timeinfo, "%H:%M:%S");
  Serial.println(&timeinfo, "%H:%M:%S");

  lcd.setCursor(0, 1);
  lcd.println(&timeinfo, "%Y-%m-%d   %Z");
  Serial.println(&timeinfo, "%Y-%m-%d   %Z");
}
void setTimezone(String timezone){
  Serial.printf("  Setting Timezone to %s\n",timezone.c_str());
  setenv("TZ",timezone.c_str(),1);  //  Now adjust the TZ.  Clock settings are adjusted to show the new local time
  tzset();
}

void setTime(int yr, int month, int mday, int hr, int minute, int sec, int isDst){
  struct tm tm;

  tm.tm_year = yr - 1900;   // Set date
  tm.tm_mon = month-1;
  tm.tm_mday = mday;
  tm.tm_hour = hr;      // Set time
  tm.tm_min = minute;
  tm.tm_sec = sec;
  tm.tm_isdst = isDst;  // 1 or 0
  time_t t = mktime(&tm);
  Serial.printf("Setting time: %s", asctime(&tm));
  struct timeval now = { .tv_sec = t };
  settimeofday(&now, NULL);
}