//PROGRAM TO DISPLAY " ETALVIS" on line2,rotate left to right continuosly.

//d0-d7 on port f and e and rs on portk

volatile uint8_t *outf,*outk;
volatile uint8_t array1[] ={0x20,0x45,0x54,0x41,0x4C,0x56,0x49,0x53,0x20,0x45,0x54,0x41,0x4C,0x56,0x49,0x53};
volatile uint8_t address;
volatile uint8_t j,i,p=9;
volatile int z=15,q=15;
volatile uint32_t k;
void setup() {
  // put your setup code here, to run once:
volatile uint8_t *dirf,*dirk;
dirf=0x30,dirk=0x107;
*dirf=0xff;*dirk=0x03;

}

void loop() {
  // put your main code here, to run repeatedly:
outf=0x31;outk=0x108;
initialize();
for(i=0;i<16;i++){//array1 entering
address=0xc0+i;
for(j=0;j<=i;j++){
  *outk=0x00;
*outf=address-j;
pulse_enable_command();
if(j==0){//left to right entering
*outk=0x02;
*outf=array1[z];
pulse_enable_data();
}
else{
*outk=0x02;
*outf=array1[z-j];
pulse_enable_data();
}
}
for(k=0;k<100000;k++);
}
while(1){
  q=15;z=15;
for(i=0;i<16;i++){//array1 leaving
address=0xcf;
q--;
for(j=0;j<=14-i;j++){
  *outk=0x00;
*outf=address-j;
pulse_enable_command();
if(j==0){//left to right entering
*outk=0x02;
*outf=array1[q];
pulse_enable_data();
}
else{
*outk=0x02;
*outf=array1[q-j];
pulse_enable_data();
}
}
address=0xc0+i;//array2 entering
for(j=0;j<=i;j++){
  *outk=0x00;
*outf=address-j;
pulse_enable_command();
if(j==0){//left to right entering
*outk=0x02;
*outf=array1[z];
pulse_enable_data();
}
else{
*outk=0x02;
*outf=array1[z-j];
pulse_enable_data();
}
}
for(k=0;k<100000;k++);
}
}
}

void initialize(){
  for(k=0;k<10000;k++);//15ms wait
  //function set 2lines and 8 columns
  *outk=0x00;// using lcd in command mode
  *outf=0x38;//putting data
  pulse_enable_command();
  //turning the display ON
  *outk=0x00;// using lcd in command mode
  *outf=0x0c;//putting data
  pulse_enable_command(); 
  //clearing display
  clear_display();
}

void pulse_enable_data(){
    *outk=0x03;//pulsing e
  for(k=0;k<100;k++);
  *outk=0x02; 
}

void pulse_enable_command(){
    *outk=0x01;//pulsing e
  for(k=0;k<100;k++);
  *outk=0x00; 
}

void clear_display(){
  *outk=0x00;// using lcd in command mode
  *outf=0x01;//putting data
  pulse_enable_command();
}