//
//  H0 by FreeRTOS kopie poslední odladěné verze 25 s WiFi, NTP, Serials=NEX, I2C, PCF, PCA
//  úpravy #ifdef ...
//  na zdroje náročná FastLED nahrazena úspornější a jednodušší Adafruit_NeoPixel - funguje dobře

//#define DEBUG       // Pokud zakomentuju nebo smažu, blok se nepřeloží
#define WIFI          // obsluha WiFI    
#define NEX           // obsluha next.h
#define PWM           // obsluha pwm_PCA.h    
#define PCF           // obsluha PCF.h
#define WSLED         // když to spustím tak asi koliduje s i2c - PCA blink nebliká, PCF nezrcadlí...

#include "defs.h"                 //  deklarace společných proměnných
#include <Wire.h>                 //  arduino knihovna i2c
#include <LiquidCrystal_I2C.h>    // arduino knihovna lcd
#include "I2C.h"                  // podprogramy pro konunikaci po I2C

#ifdef WIFI
#include <WiFi.h>
#endif
//#ifdef NTP                      // NTP vždy pokud WIFI
//#include "NTP.h"
//#endif

#define NTP_SERVER     "pool.ntp.org"
#define UTC_OFFSET     0
#define UTC_OFFSET_DST 0
#define timeout        5000      // 5 seconds   WiFi connection timeout


#ifdef NEX
#include "NEX_routines.h"
uint8_t NEX_m_length;      // length of available new message form Serial2
#endif

//byte dataBuffer[16];

#ifdef WSLED
#include <Adafruit_NeoPixel.h>
#define NUM_LEDS 16
#define DATA_PIN 15
Adafruit_NeoPixel pixels(NUM_LEDS, DATA_PIN, NEO_GRB + NEO_KHZ800);
#endif

#ifdef PWM
#include "PCA_routines.h"
#endif

#ifdef PCF
#include "PCF_routines.h"
uint16_t pcf_inputs;
#endif

//uint8_t error;
unsigned long duration, period, start, finished, elapsed;     // pomocne pro time
uint8_t j;


QueueHandle_t xFila;
SemaphoreHandle_t xSerialSem;
SemaphoreHandle_t xSerialSem2;

TaskHandle_t Task1;         // PCF
TaskHandle_t Task2;         // Serial, NEX
TaskHandle_t Task3;         // PWM(PCA)
TaskHandle_t Task4;         // print local time
TaskHandle_t Task5;         // WiFim NTP
TaskHandle_t Task6;         // WSLED

int connected = 0;
int tamFila = 200;

void setup() {

  Serial.begin(115200);                               //  hwUART0 default pins RX=GPIO3 TX=GPIO1, can be remapped
  Serial.println("Hello, H0 by ESP32!");

//  Serial.println(F(__FILE__ " " __DATE__ " " __TIME__));  //File compiler details

//Serial1.begin(9600);                                //  hwUART1 e.g. pins RX=GPI09 TX=GPI10, flash memory conflict..
  Serial.setTimeout(100); // Set timeout todefault is 1 seconds
#ifdef NEX
  Serial2.begin(9600, SERIAL_8N1, 16, 17);            //  hwUART2 e.g. pins RX=GPI16 TX=GPI17 for Nextion serial
  Serial2.setTimeout(50);                             // Set timeout to miliseconds - v simulaci nejlíp 50msec
#endif NEX

/*
#ifdef WSLED
  pixels.begin(); // INITIALIZE NeoPixel strip object (REQUIRED)
#endif
*/

/*
#ifdef PWM
  PCA_setup();
#endif
*/

  if (xSerialSem == NULL)
  {
    xSerialSem = xSemaphoreCreateMutex();
    if (xSerialSem != NULL)
      xSemaphoreGive(xSerialSem);
  }

  if (xSerialSem2 == NULL)
  {
    xSerialSem2 = xSemaphoreCreateMutex();
    if (xSerialSem2 != NULL)
      xSemaphoreGive(xSerialSem2);
  }

  xFila = xQueueCreate( tamFila, sizeof( String ) );
  if(xFila == NULL){
  Serial.println("Erro criando fila");
  }

  // put your setup code here, to run once:
  lcd.init();
  lcd.backlight();
  lcd.clear();
  lcd.setCursor(0, 0);
  lcd.println("H0 Railway ESP32");
  lcd.setCursor(0, 1);
  lcd.println("freeRTOS   v: 21");

// best safe use hwUART2: pins RX=GPI16/TX=GPI17 independent off usb programming,boot/loop,internal memory, wifi etc

  Wire.begin();                                       // běží s default parametry
  Wire.setClock(Wire_FREQ);
//  Wire.begin(SDA, SCL, Wire_FREQ);                  // možnost změny default parametrů
// !!! Wire1.begin();                                    // nefunguje bez zadání pinů
  Wire1.begin(SDA_1, SCL_1, Wire_1_FREQ);             //  druhá sběrnice, deklarace parametrů v I2C.h                                    //

//  Serial.println("Hello, H0 by ESP32!");
//  vTaskDelay(pdMS_TO_TICKS(500));

//  scan i2c proběhne v setupu před spuštěním tasků
//  I2C_scan(0);            // scan systemové sběrice Wire()
//  I2C_scan(1);            // scan sběrnice Wire1()


//xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

//#ifdef PCF
  xTaskCreatePinnedToCore(
      Task1code, /* Task function. */
      "Task1",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task1,    /* Task handle to keep track of created task */
      1);        /* pin task to core 0 */
//#endif

//#ifdef NEX
  xTaskCreatePinnedToCore(
      Task2code, /* Task function. */
      "Task2",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task2,    /* Task handle to keep track of created task */
      1);        /* pin task to core 1 */
//#endif

//#ifdef PWM
  xTaskCreatePinnedToCore(
      Task3code, /* Task function. */
      "Task3",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task3,    /* Task handle to keep track of created task */
      1);        /* pin task to core 1 */
//#endif

//#ifdef xxx
  xTaskCreatePinnedToCore(
      Task4code, /* Task function. */
      "Task4",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task4,    /* Task handle to keep track of created task */
      1);        /* pin task to core 1 */
//#endif

//#ifdef WIFI
  xTaskCreatePinnedToCore(
      Task5code, /* Task function. */
      "Task5",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task5,    /* Task handle to keep track of created task */
      1);        /* pin task to core 1 */
//#endif
  xTaskCreatePinnedToCore(
      Task6code, /* Task function. */
      "Task6",   /* name of task. */
      10000,     /* Stack size of task */
      NULL,      /* parameter of the task */
      1,         /* priority of the task */
      &Task6,    /* Task handle to keep track of created task */
      1);        /* pin task to core 1 */


//xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

//  vTaskDelay(pdMS_TO_TICKS(500));

Serial.println("verze Serial2.readstring, timeout 50ms ještě potřeba dodělat parsing");

}
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////   main loop   //////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
void loop() {

  delay(10); // this speeds up the simulation

/*    zkouška práce se struct
A_track_control[8].direction_s = 63;
Serial.println(A_track_control[8].direction_s);
*/

#ifdef NEX
//  nex_read_data();
  /*  if (dataReady) {              // dataReady deklarovano v NEX_routines
    nex_parse_data();
  }  */
  dataReady = false;
//Serial2.print("j0.val=25");
//sendTermination();
#endif NEX


//#ifdef PWM
//  Serial.println(millis());
//    write_pwm();            //   trvá cca 
//    write_pwm_blink();
//  Serial.println(millis());
//#endif

// vTaskDelay(pdMS_TO_TICKS(1000));

/*    zkouška práce se struct
A_track_control[8].direction_s = 63;
Serial.println(A_track_control[8].direction_s);
*/

}

/*******************************************************************************************************************/
void spinner() {
  static int8_t counter = 0;
  const char* glyphs = "\xa1\xa5\xdb";
  lcd.setCursor(15, 1);
  lcd.print(glyphs[counter++]);
  if (counter == strlen(glyphs)) {
    counter = 0;
  }
}

void setTimezone(String timezone){
  Serial.printf("  Setting Timezone to %s\n",timezone.c_str());
  setenv("TZ",timezone.c_str(),1);  //  Now adjust the TZ.  Clock settings are adjusted to show the new local time
  tzset();
}

// setting the internal ESP32 RTC
void setTime(int yr, int month, int mday, int hr, int minute, int sec, int isDst){
  struct tm tm;
  tm.tm_year = yr - 1900;   // Set date
  tm.tm_mon = month-1;
  tm.tm_mday = mday;
  tm.tm_hour = hr;      // Set time
  tm.tm_min = minute;
  tm.tm_sec = sec;
  tm.tm_isdst = isDst;  // 1 or 0
  time_t t = mktime(&tm);
  Serial.printf("Setting time: %s", asctime(&tm));
  struct timeval now = { .tv_sec = t };
  settimeofday(&now, NULL);
}

void printLocalTime_F()
{
  struct tm timeinfo;
  if (!getLocalTime(&timeinfo)){
      lcd.setCursor(0, 1);
      lcd.println("Connection Err");
      connected = 0;
      return;
    }

//      lcd.clear();
//      lcd.setCursor(0, 0);
//      lcd.println("                ");
      lcd.setCursor(8, 0);
      lcd.println(&timeinfo, "%H:%M:%S");
           lcd.setCursor(0, 1);
    lcd.println(&timeinfo, "%d/%m/%Y   %Z");
}

//xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

void Task1code(void *pvParameters) {
  Serial.print("Task1 running on core ");
  Serial.println(xPortGetCoreID());
  for (;;)
  {
      if (xSemaphoreTake(xSerialSem2, (TickType_t)5 == pdTRUE)){
    Serial.println("Task 1");

#ifdef PCF
// PCF readings
  i2c_bus = 0;          // select system i2c bus (wire())
  pcf_inputs = ~pcf8575_read(i2c_bus,0x21);                     // testování read
  Serial.println("PCF8575_21 wire : ");
  Serial.println(pcf_inputs,BIN);

  i2c_bus = 1;          // select (wire1) i2c bus
  tcaselect(0);         // přepínání kanálů funguje, TCA na sběrnici 1 (Wire1())

  pcf_inputs = ~pcf8575_read(i2c_bus, 0x22);
  pcf8575_write(0, 0x22, pcf_inputs);                           // miror, testování write

  hall_A = ~pcf8575_read(i2c_bus, 0x22); // ukládám to na zkoušku do uint16_t hall_A a podle toho budu rozsvěcet WSLED

  pcf_inputs = ~pcf8575_read(i2c_bus, 0x23);
  pcf8575_write(0, 0x23, pcf_inputs);                           // miror testování write
#endif PCF

          xSemaphoreGive(xSerialSem2);
      }
    vTaskDelay(100);
    }
}

void Task2code(void *pvParameters) {
  Serial.print("Task2 running on core ");
  Serial.println(xPortGetCoreID());
  for (;;)
  {
  #ifdef NEX
//    Serial.println("Task 2");

  String dataBuffer = "";

  // Kontrola, zda jsou v bufferu vůbec nějaká data k dispozici
      if (Serial.available() > 0) {
    // Načte text ze sériové linky, dokud nenarazí na odřádkování ('\n')    // to ale NEX neposílá

    String dataBuffer = Serial.readStringUntil('ÿ');   // ukončí při prvním znaku 0xFF,
          //ale z NEX jdou ještě další dva 0xFF které načte ve dvou čtec.cyklech jako prázdné message
    
    dataBuffer.trim();    // Odstraní případné neviditelné znaky na konci (např. '\r' při CR+LF)

    m_length = dataBuffer.length();
    Serial.print("Received from Serial ");
    Serial.print(m_length);
    Serial.println(" byte, indexed output :");
    for(uint8_t index = 0; index < m_length+1; index++)
      {
        Serial.print(dataBuffer[index]);        // mohu pracovat s jednotlivými byte pole
      }
    Serial.println("");
    Serial.print("dataBuffer : ");
    Serial.println(dataBuffer);
    Serial.println(".....");

    Serial2.print(dataBuffer);
    Serial2.write(0xFF);
    Serial2.write(0xFF);
    Serial2.write(0xFF);
  }

      if (Serial2.available() > 0) {
    dataBuffer = Serial2.readString();

    if(dataBuffer.length()>0) {
//    if(dataBuffer.length()>0 && dataBuffer.startsWith("e",0) && dataBuffer.endsWith("ÿÿÿ")) {

        if(dataBuffer.startsWith("e",0))  Serial.println("starts with e");
        if(dataBuffer.endsWith("ÿÿÿ")) Serial.println("ends with ÿÿÿ");
///    if((dataBuffer.substring(1) == 'ÿÿÿ')) Serial.println("dataBuffer.substring(1) == ÿÿÿ");     // nějak NEFUNGUJE
    if(dataBuffer.substring(4) == "ÿÿÿ") Serial.println("dataBuffer.substring(4) == ÿ");   // nějak NEFUNGUJE

    Serial.print("dataBuffer : ");
    Serial.println(dataBuffer);
    }
    if(dataBuffer.length()>0) 
     {
    NEX_touch = dataBuffer[0];    // Touch Event
    if(NEX_touch == 0x65){

    NEX_page  = dataBuffer[1];    // Touch Event
    NEX_id    = dataBuffer[2];    // Attribute id
    NEX_value = dataBuffer[3];    // Attribute value

Serial.print("Code : 0x");
Serial.println(NEX_touch,HEX);
Serial.print("Page : ");
Serial.println(NEX_page);
Serial.print("Component : ");
Serial.println(NEX_id);
Serial.print("Value : ");
Serial.println(NEX_value);
      }
  else{
    Serial.print("Received from Serial2 ");
    for(uint8_t index = 0; index < m_length; index++)
      {
        Serial.print(":");
        Serial.print(dataBuffer[index],HEX);        // mohu pracovat s jednotlivými byte pole, HEXa výpis
      }
    Serial.println("");
    Serial.print("dataBuffer : ");
    Serial.println(dataBuffer);
    Serial.println("");
//    Serial.println(" <<");
      }
    Serial.println("");
    }
  }
    vTaskDelay(50);         // čím delší tím méně stíhá zparcovat následující telegram a načte 2 i více do datBufferu
                            // zkusit si pohrát se semafory a ? queue frontou ? - pak ale jiné vyhodnocení stringu dataBuffer
                            // a nebo nechat a bude ignorovat příliš rychlé povely z NEX
                            // možná to "zdržujou" i Serial.print() prozatimních výpisů;
                            // povely budu ukládat zrychleně do příslušných struct....
  #endif
  }
}
void Task3code(void *pvParameters)
{
  Serial.print("Task3 running on core ");
  Serial.println(xPortGetCoreID());
  #ifdef PWM
    PCA_setup();
  #endif
  for (;;)
  {
  #ifdef PWM
    Serial.println("Task 3");
    write_pwm_blink1();
    vTaskDelay(500);
    write_pwm_blink2();
    vTaskDelay(500);
  #endif
////    vTaskDelay(50);
  }
}
void Task4code(void *pvParameters)              // printLocalTime
{
  Serial.print("Task4 running on core ");
  Serial.println(xPortGetCoreID());
// Serial.println("Temp: " + String(dht.readTemperature(), 1) + " \260C");
// Serial.println("Hum: " + String(dht.readHumidity(), 1) + " %");
  
  for (;;)
  {
 
    if( connected == 1){
      if (xSemaphoreTake(xSerialSem, (TickType_t)5 == pdTRUE)){
/*        
          if (xSemaphoreTake(xSerialSem2, (TickType_t)10 == pdTRUE)){
            xSemaphoreGive(xSerialSem2);
          } 
*/
          printLocalTime_F();
          vTaskDelay(1000);
          xSemaphoreGive(xSerialSem);

        }
    }else{
      vTaskDelay(500);
    }
  }
}

void Task5code(void *pvParameters)              // WiFi NTP
{
  Serial.print("Task5 running on core ");
  Serial.println(xPortGetCoreID());
  for (;;)
  {
  #ifdef WIFI
    if( connected == 0){
      if (xSemaphoreTake(xSerialSem, (TickType_t)5 == pdTRUE)){
          
          Serial.println("Task 5 - connecting WiFi");

          lcd.setCursor(0, 0);
          lcd.print("Connecting to   ");
          lcd.setCursor(0, 1);
          lcd.print("WiFi            ");

          WiFi.begin("Wokwi-GUEST", "", 6);       // channel 6
          while (WiFi.status() != WL_CONNECTED)
          {
            vTaskDelay(10);
            spinner();
          }

          Serial.println("");
          Serial.println("WiFi connected");
          Serial.print("IP address: ");
          Serial.println(WiFi.localIP());

          lcd.clear();
          lcd.setCursor(0, 0);
        //  lcd.println("FreeRTOS   H0_21");
          lcd.println("Online          ");
          lcd.setCursor(0, 1);
          lcd.println("Updating time...");

          connected = 1;

          configTime(UTC_OFFSET, UTC_OFFSET_DST, NTP_SERVER);
          setTimezone("CET-1CEST,M3.5.0,M10.5.0/3");
          
          xSemaphoreGive(xSerialSem);
          Serial.print("Status: ");
          Serial.println(connected);

      }
  Serial.println("Task 5");
  }
  #endif
  vTaskDelay(1000);
 }
}
void Task6code(void *pvParameters)                // WSLED
{
  // asi občas trochu časová kolize ? s i2c ... pořešit Semaforem
  // nejspíš čtení vs zápis od PCF
  // v principu to funguje

  Serial.print("Task6 running on core ");
  Serial.println(xPortGetCoreID());
  #ifdef WSLED
  pixels.begin(); // INITIALIZE NeoPixel strip object (REQUIRED)
  #endif
  for (;;)
  {
  #ifdef WSLED
    Serial.println("Task 6");
//    pixels.clear(); // Set all pixel colors to 'off'

  for(int i=0; i<16; i++) { // For each pixel...
    hall_A & (1<<i) ? pixels.setPixelColor(i, pixels.Color(0, 255, 0)) : pixels.setPixelColor(i, pixels.Color(255, 0, 0));
    pixels.show();   // Send the updated pixel colors to the hardware.
  }
  vTaskDelay(200);

  #endif
  }
}